KORG MICROX X50 - Manual (Page 147)

140
69: Comp–M.Dly
(Compressor – Multitap Delay)
This effect combines a mono-type compressor and a multitap
delay. You can change the order of the effect connection.
70: Limit–P4EQ
(Limiter – Parametric 4-Band EQ)
This effect combines a mono-type limiter and a four-band
parametric equalizer. You can change the order of the effect
connection.
a
[CMP] Sensitivity
Sets the sensitivity 1...100
☞ Fx:02
b
Attack
Sets the attack level 1...100
☞ Fx:02
Level (Output Level)
Sets the compressor output level 0...100
☞ Fx:02
c
Pre EQ Trim
Sets the EQ input level 0...100
d
LoEQ (Pre Low EQ Gain)
Sets the gain of Low EQ –15...+15dB
HiEQ (Pre High EQ Gain)
Sets the gain of High EQ –15...+15dB
e
[DLY] T1 (Tap1 Delay)
Sets the Tap1 delay time 0...680msec
T2 (Tap2 Delay)
Sets the Tap2 delay time 0...680msec
f
T1 Level (Tap1 Level)
Sets the Tap1 output level 0...100
☞ Fx:45
T2 (Tap2 Delay)
Sets the Tap2 feedback amount –100...+100
g
Dly W/D (Delay Wet/Dry) Dry, 1:99...99:1, Wet
Sets the multitap delay effect balance
HiDamp (High Damp)
Sets the damping amount in the high range 0...100%
☞ Fx:43
h
[Routing] CMP → DLY, DLY → CMP
Switches the order of the compressor and multitap delay connection
i
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Routing
Compressor
LEQ HEQ EQ Trim
Output Level
Envelope - Control
Multitap Delay
Feedback
High Damp
Delay
(2)
(1)
Mt.Dly Wet / Dry
Comp
a
[LMT] Ratio 1.0:1...50.0:1, Inf:1
Sets the signal compression ratio ☞ Fx:03
b
Threshld (Threshold) –40...0dB
Sets the level above which the compressor is applied ☞ Fx:03
G.Adj (Gain Adjust)
Sets the limiter output gain –Inf, –38...+24dB
☞ Fx:03
c
Attack
Sets the attack time 1...100
☞ Fx:03
Release
Sets the release time 1...100
☞ Fx:03
d
[PEQ] Trim
Sets the parametric EQ input level 0...100
e
[Routing] LMT → PEQ, PEQ → LMT
Switches the order of the limiter and parametric EQ connection
f
B1 (Band1 Cutoff)
Sets the center frequency of Band 1 20...1.00kHz
Q
Sets the bandwidth of Band 1 0.5...10.0
☞ Fx:06
G (Gain)
Sets the gain of Band 1 –18...+18dB
g
B2 (Band2 Cutoff)
Sets the center frequency of Band 2 50...5.00kHz
Q
Sets the bandwidth of Band 2 0.5...10.0
☞ Fx:06
G (Gain)
Sets the gain of Band 2 –18...+18dB
h
B3 (Band3 Cutoff)
Sets the center frequency for Band 3 300...10.00kHz
Q
Sets the bandwidth of Band 3 0.5...10.0
☞ Fx:06
G (Gain)
Sets the gain of Band 3 –18...+18dB
i
B4 (Band4 Cutoff)
Sets the center frequency for Band 4 500...20.00kHz
Q
Sets the bandwidth of Band 4 0.5...10.0
☞ Fx:06
G (Gain)
Sets the gain of Band 4 –18...+18dB
j
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Routing
Limiter
Trim
Parametric 4Band EQ
Limiter
Gain Adjust
Envelope - Control