KORG MICROX X50 - Manual (Page 37)

30
PROG 9: Ed–MasterFX
☞For details on master effects, refer to p.97 “6. Effect
Guide.”
9–1: Setup
Here you can select the master effect types, switch them on/
off, specify chain order, and set the master EQ.
9–1a: Master Effect Setup
The master effects do not output the direct sound (Dry). The
return level (“Rtn 1, 2”) sends the effect sound (Wet) to the L
and R bus, and this is mixed with the direct sound (“BUS
Select” L/R: 8–1a, 8–2a).
The master effects are monaural input. The sound that is
panned to L and R after passing through the oscillator and
insert effect is mixed to a monaural signal as adjusted by the
“S1 (Send1(MFX1))” and “S2 (Send2(MFX2))” levels, and
input to the master effects.
The master effects are mono-in stereo-out. Even when
a stereo-input type effect is selected, the input will be
monaural.
MFX1 On/Off, MFX2 On/Off [Off, On]
Switches master effect 1, 2 on/off. When off, the output will
be muted.
Separately from this setting, you can use CC#94 to switch
master effect 1 on/off, CC#95 to switch master effect 2
on/off. A value of 0 will be off, and a value of 1–127 will
be the original setting. This is controlled on the global
MIDI channel “MIDI Channel” (GLOBAL 1–1a).
Master Effect 1, 2 [00...89: name]
Indicates the effect type for master effect 1, 2. You can select
from 89 types of effect: 01: St.Amp Sim–89: Reverb-Gate. If
00: No Effect
is selected, the output from the master effect
will be muted.
Rtn 1, 2 (Return 1, 2) [000...127]
Adjusts the return levels from the master effects to the L/R
bus (main output L/MONO, R).
9–1b: Chain
MFX Chain [Off, On]
On (checked): Chain (series connection) will be turned on
for MFX1 and MFX2. ( ☞p.102)
Off (unchecked): MFX 1 and MFX2 are operating in parallel.
Direction (Chain Direction)
[MFX1
→MFX2, MFX2→MFX1]
Specifies the direction of the connection when MFX1 and
MFX2 are chained.
MFX1 →MFX2: Connect from MFX1 to MFX2.
MFX2 →MFX1: Connect from MFX2 to MFX1.
Signal (Chain Signal) [L/R Mix, L Only, R Only]
When chain is On, this parameter specifies how the stereo
output signal of the first master effect will be connected to
the input (mono) of the next master effect.
L/R Mix: The stereo output L/R of the first master effect will
be mixed before being input to the next master effect.
L Only, R Only:
Only the left or right channel of the output
will be input to the next master effect.
Level (Chain Level) [000...127]
Sets the send level from the first master effect to the next
master effect when chain is turned on.
9–1c: Master EQ Gain [dB]
Sets the amount of cut and boost for the three-band EQ
located immediately before the (MAIN OUTPUT) L/MONO
and R jacks. This is linked with the various “Gain” parame-
ters of Master EQ (9–4).
Low [–18.0...+18.0]
Mid [–18.0...+18.0]
High [–18.0...+18.0]
The cutoff frequency for “Low,” “Mid” and “High” and the
“Q” of “Mid” can be adjusted in the MEQ page. These set-
tings are in “dB” units.
■ 9–1: UTILITY
☞“Write Program” (0–1)
For details on how to select the desired utility function, refer
to “PROG 0–1: UTILITY.”
Copy Master Effect
This command lets you copy any desired effect settings from
Program, Combination, Muliti set.
1 Select “Copy Master Effect” to access the dialog box.
2 In “From,” select the copy source mode, bank, and num-
ber.
X50: You can press a PROG BANK button to select a bank.
You can also use numeric buttons [0]–[9] and the [ENTER]
button to select a number.
9–1a
9–1b
9–1c