KORG MICROX X50 - Manual (Page 47)

40
COMBI 2: Ed–Timbre Param
2–1: MIDI
Here you can make MIDI settings for each timbre.
2–1a: Status, MIDI Channel, Bank(EX2)
MSB/LSB
Status [INT, Off, EXT, EX2]
Specifies the status of MIDI and the internal tone generator
for each timbre.
INT:
When you play this instrument, the internal tone gen-
erator will sound, and will also sound in respond to MIDI
messages received from an external MIDI device. MIDI data
will not be transmitted.
Off:
The program will not sound. Nor will MIDI data be
transmitted.
EXT:
Playing this instrument will not cause it to sound, but
it will transmit data via MIDI to control external MIDI
devices.
EX2
: “Bank (EX2) MSB” and “Bank (EX2) LSB” (2–1a) will be
enabled. Instead of the bank numbers for A–G(d) that can be
selected on this instrument, the bank numbers you specify
here will be transmitted via MIDI. In other respects this is
the same as EXT.
MIDI Channel [01...16, Gch]
Set the MIDI transmit/receive channel for each timbre 1–8.
Gch:
The timbre will use the channel that has been selected
as the global MIDI channel “MIDI Channel” (GLOBAL 1–
1a).
When “Status” is INT, MIDI messages will be received on
the channel you specify here. If this setting is the same as the
global MIDI channel, the internal tone generator will sound
according to the internal settings. If this is set to EXT or EX2,
playing this instrument will transmit MIDI messages on the
MIDI channel specified here. (Messages will also be trans-
mitted simultaneously on the global MIDI channel.)
Bank(EX2) MSB [000:000...127:127]
Bank(EX2) LSB [000:000...127:127]
Specifies the bank number that will be transmitted when
“Status” is set to EX2. If “Status” is not set to EX2, this set-
ting has no effect.
■ 2–1: UTILITY
☞“Write Combination,” “Solo Selected Timbre” (0–1)
2–2: OSC
These settings specify how each timbre will be sounded.
2–2a: Force OSC Mode, OSC Select, Porta-
mento
Force OSC Mode [PRG, Poly, Mono, LGT]
Specifies the “Mode (Voice Assign Mode)” (PROG 1–1b) of
the program selected for each timbre 1–8.
PRG:
The settings of the program will be used.
Poly: The timbre will play polyphonically, regardless of the
settings of the program.
Mono:
The timbre will play monophonically, regardless of
the settings of the program.
LGT (Legato):
The timbre will play monophonically, with
single triggering (legato).
With settings of Mono or LGT, the note priority will be
according to the “Priority” (PROG 1–1b) setting of the pro-
gram.
OSC Select [Both, OSC1, OSC2]
Specifies the “Mode (Oscillator Mode)” (PROG 1–1a) of the
program selected for each timbre 1–8. If the “Mode (Oscilla-
tor Mode)” is Double, you can specify that either or both
oscillators sound.
Both:
OSC1 and 2 will sound as specified by the settings of
the program.
OSC1:
Only OSC1 will sound.
OSC2: Only OSC2 will sound. If “Mode (Oscillator Mode)”
is Single or Drums, there will be no sound.
Portamento [PRG, Off, 001...127]
Indicates portamento settings for each timbre 1–8.
PRG:
Portamento will be applied as specified by the pro-
gram settings.
Off:
Portamento will be off, even if the original program set-
tings specified for it to be on.
001...127:
Portamento will be applied with the portamento
time you specify here, even if it is turned off by the program
settings.
If the “Status” (2–1a) is set to INT, CC#05 (portamento
time) and CC#65 (portamento switch) messages will be
received to control and change this setting. (If the set-
ting is PRG, CC#05 portamento time will not be
received.) These messages will be received on the MIDI
channel specified for each timbre by “MIDI Channel”
(2–1a).
■ 2–2: UTILITY
☞“Write Combination,” “Solo Selected Timbre” (0–1)
2–1a
Tone
generator
MIDI IN
INT
MIDI OUT
EXT, EX2
2–2a