Philips MAGIC 5 ECO PPF 695 - Manual (Page 38)

38 Philips PPF 685 · 695
EN
Setting line interruption
Function is not supported in all countries and networks (Function is not supported in all countries and
networks)
Setting line interruption
The necessary length of the short line interruption (Hook
Flash) depends on the country and telephone network.
The Hook Flash period is set in the device by the factory,
if you have selected the correct country, in which you op-
erate your device. If you cannot call special functions or
dial outside from an extension, you must probably change
the Hook Flash time (country and network-dependent).
Inquire with your telephone company or find out by trial
and error with which settings these services function.
1 Press
OK, 24 and OK.
2 Using the
[ key, select the length of the Hook Flash
signal to the switching centre in the public switched tel-
ephone network (PSTN). Change this setting, if you
cannot call additional telephone functions such as call
on hold, three-way call or forwarding.
3 Confirm with
OK.
4 Using the
[ key, select the length of the Hook Flash
signal to the switching centre of a private automatic
branch exchange (PABX). If the outside line access
code of your telephone system is R (= Flash), set here-
with the length of the signal for getting the outside line.
5 Confirm with
OK.
Setting the Ring Tone
Selecting the Ring Tone
Ring Tones
You can select from among ten different ring tones.
1 Press
OK, 55 and OK.
2 Use the number buttons
0 to 9 to select a ring
tone. Using
[, set the volume.
3 Confirm with
OK.
Setting the Volume
Setting the Ring Tone Volume
You can adjust the volume of the ring tone when the device
is ringing or when you set the ring tone. You can save dif-
ferent volumes for the
™ (day) and ˜ (night) modes, (also
see Chapter Fax Switch).
Setting the Volume on the Machine
Using
[ you can set adjust the volume when the device
is ringing.
Setting the Fax Switch
Fax switch
The built-in fax switch of your device distinguishes be-
tween fax messages and telephone calls. Faxes are automat-
ically received, telephone calls can be received—even on
additionally connected devices. While the device is check-
ing the call, it continues to ring.
Day and Night Mode
You can set how often the device should ring before pick-
ing up separately for the modes
™ (day) and ˜ (night). This
makes it possible for you to receive faxes silently at night
without getting disturbed.
Press
¼/º/» to switch between day and night mode.
With the activated timer › , the device switches between
the modes ™ (day) and ˜ (night) at the configured times.
Only Fax Reception
In the fax only reception mode ( F on the display) the de-
vice rings twice. Then the fax reception switches on (this
function is not supported in all countries and networks).
Configuring Day Mode
1 Press
OK, 51 and OK.
2 Using
[ select the number of rings for the answering
machine. The answering machine responds after these
many number of rings.
3 Confirm with
OK.
4 Use
[ to select the number of rings for the fax switch.
After the number of rings, the fax switch switches on
and distinguishes between fax transmissions and tele-
phone calls. While the device is checking the call, it
continues to ring.
5 Confirm with
OK.
6 Using
[, set the volume.
7 Confirm with
OK.
Silent fax transmission
Configuring Night Mode
1 Press
OK, 52 and OK.
2 Configure the same settings as for the day mode (see
steps 2 to 7).
If your device is not connected to a PABX or if
your PABX system uses another outside line ac-
cess code (for example
0), this setting has no ef-
fect.
If you select the 5/2 option for the number of
rings of the answering machine, the answering
machine switches on after two rings, when you
have received new messages. If there are no new
messages, the device rings five times. If the device
does not pick up after two rings, you have no new
messages. You can terminate the remote access
without incurring any telephone costs.
Older devices do not transmit any fax-tone (= CNG
tone) as an announcement for fax transmission (= si-
lent fax transmission). If the total number of rings
has been set to a value using
7 , silent fax transmis-
sions cannot be received automatically.