Panasonic KX-T206E - Manual (Page 28)

28
System Programming
Other Programs
• Host PBX Access Code Assignment
Assigns a Host PBX access code to make an
outside call, if the system is installed behind the
host PBX. A pause is automatically inserted
after the access code and the toll restriction
feature applies to the number after the code.
Input Format: #21 [A] [code] #
• [A]=1: CO1/ 2: CO2
• [code] = 2 digits max. (Default : Not stored)
• Hookswitch Flash Time Assignment
Sets the time to send the flash signal to each CO
line.
Input Format: #22 [A] [B]
• [A]=1: CO1/ 2: CO2
• [B]=0: 80 ms/ 1: 100 ms (default)/ 2: 160 ms/
3: 300 ms/ 4: 600 ms / 5: 900 ms /
6: 1200 ms
• CO Pulse Selection
Assigns to send the pulse to CO line during a
conversation with an outside party when the “#01
Dial Type Selection” program is assigned as
“Pulse”.
Input Format: #23 [A]
• [A]=0: DISABLE/ 1: ENABLE (default)
• Call Incoming Mode Selection
Assigns whether to use the DISA feature or not.
This program is available when the DISA/FAX
Detect card is installed.
Input Format: #24 [A] [B]
• [A]=1: CO1/ 2: CO2
• [B]=0: NORMAL (default)/ 1: DISA
• Bell Off Detection
Sets the time between one bell signal detection
and the next signal from a Central Office.
Input Format: #25 [A]
• [A]=1: 6 SEC/ 2: 3 SEC (default)
• Intercom Alerting Assignment
Assigns the intercom alerting mode to each
extension when an intercom call reaches.
Input Format: #30 [A] [B]
• [A]=1 through 6 (corresponding to extension
no. 21 through 26)
• [B]=0: TONE (default)/ 1: VOICE
• Paralleled Telephone Connection
Assigns whether each extension will be con-
nected in parallel with a single line telephone or
not.
Input Format: #31 [A] [B]
• [A]=1 through 6 (corresponding to extension
no. 21 through 26)
• [B]=0: DISABLE (default)/ 1: ENABLE
• Tone Waiting Time After OGM
Sets the time between sending an outgoing
message and sending the ringback tone.
Input Format: #40 [A]
• [A]=0: 0 SEC/ 1: 5 SEC (default)/ 2: 10 SEC/
3: 15 SEC
• Hold Recall Time
Assigns the length of the hold recall timer and
transfer recall timer. The hold recall timer is
used to alert an extension that a call has been
held for an extended period of time. The
transfer recall timer is used to alert an extension
that a transferred call has not been answered for
an extended period of time.
Input Format: #50 [A]
• [A]=0: 30 SEC (default)/ 1: 1 MIN / 2: 2 MIN/
3: 3 MIN/ 4: 4 MIN/ 5: DISABLE
• Hold Mode Selection for SLT
Assigns the method to put a call on hold with
SLTs.
Input Format: #51 [A]
• [A]=1: MODE 1 (hooking) (default)
2: MODE 2 (hooking and dial 6)
• CO Line Access Number Selection
Selects the automatic line access number.
Input Format: #52 [A]
• [A]=1: 9 (default)/ 2: 0
• Conference Tone
Assigns whether or not to delete the conference
tone. You hear the tone when the conference or
the executive busy override feature begins and
finishes.
Input Format: #53 [A]
• [A]=0: DISABLE/ 1: ENABLE (default)
• Music on Hold Use
Selects whether or not to use internal music as
the music on hold.
Input Format: #54 [A]
• [A]=1: MODE 1 (NO MUSIC) (default)/
2: MODE 2 (MUSIC)