Philips MDR515H / F7 - Manual (Page 49)

49 EN EN
Recording
Basic Setup
Connections
Playback
Editing
Introduction
Function Setup
Others
Español
How to select a channel number for the timer recording
Analog TV For channel number 2-6 press, press [ B] or [ • ] to decide the channels. For other channels (7-69),
the channel will be decided as soon as you enter the channel number.
Analog Cable
TV For channel number 1-12 press, press [ B] or [ • ] to decide the channels. For other channels (13-
125), the channel will be decided as soon as you enter the channel number.
Digital TV For channel number 1-9 press, press [ B] or [ • ] to decide the channels. For other channels (10-99),
the channel will be decided as soon as you enter the channel number.
Digital Cable TV For channel number 1-13 press, press [ B] or [ • ] to decide the channels. For other channels (14-
135), the channel will be decided as soon as you enter the channel number.
minor channels For channel number 1-9 press, press [ B] or [ • ] to decide the channels. For other channels (10-99),
the channel will be decided as soon as you enter the channel number.
<Hint>
• You can decide the 1-digit channel number by pressing 0 first , then enter desired 1-digit channel number.
e.g.) “5”: [0]+[5]
• For selecting the channels with [
K/ L] you need to press [B] or [ • ] to decide the channel number.
• For selecting the minor channels with [ K /L], please make sure the minor channel you are selecting exists.
[ K / L] does not skip the non-existing minor channels.
TIMER RECORDING
Checking, canceling, or correcting the timer
programming information
1) Press [TIMER PROG.].
2) Check the information.
Timer Programming
THU FEB/04 11:30AM SP (1:00)
FEB/05/10 10:30 AM 69.01 SP
Skip Date Start End CH
FEB/05 10:30AM 11:30AM DTV69. 1
New Program
3-A) To delete the timer program:
1 Use [ K /L] to select the program you want to
delete, then press [OK].
2 Use [
K /L] to select “Delete”, then press [OK].
Confirmation window will appear.
3 Use [
K /L] to select “Yes”, then press [OK].
3-B) To correct the timer program:
1 Use [ K /L] to select the program you want to
correct, then press [OK].
2 Use [
K /L] to select “Program Change”, then
press [OK].
3 Correct the timer program by using
[ K/ L / {/ { B], then press [OK].
4) Press [TIMER PROG.] to exit.
1) Press [STOP
C] on the remote control.
2) Confirmation message will appear. Select “Yes”, then
press [OK].
• To stop the timer recording immediately, press
[ C STOP ] on the unit.
To stop the timer recording in progress
Note
• Press [TIMER PROG.] to check the timer recording in
progress.
• As to the timer recording in progress (which is shown in red
in the timer program list), you only can edit the end time.
The changes made during recording will be recognized as
only specific to that recording in progress and it will not
affect the daily or the weekly recording setting.
Skip the Periodical Timer Recording
You can deactive the periodical (Daily, MON-SAT, MON-
FRI or Weekly) timer recording temporarily.
1) In stop mode, press [TIMER PROG.].
2) Select the periodical timer recording program you
want to skip using [ K /L], then press [OK].
3) Select “Program Change” using [ K /L], then press
[OK].
4) Move the cursor to the “Skip” field using [ { / { B],
then select “ON” using [
K/L] and then press [OK] to
activate the setting.
• “ ” will be displayed on the left side of the timer
program.
• The setting will go back to “OFF” after the program
is skipped once.
Putting Names on Timer Programs
1) In stop mode, press [TIMER PROG.].
2) Use [
K /L] to select the program you want to edit
the timer program name, then press [OK].
3) Use [ K /L] to select “Edit Title Name”, then press
[OK].
Program Change
Delete
Edit Title Name
A window for entering a title name will appear.
Timer Programming
1/1
THU FEB/04 11:30AM SP (1:00)
Skip Date Start End CH
FEB/05 10:30AM 11:30AM DTV69. 1
New Program
a b c
A B C
1 2 3
@ ! ?
FEB/05/10 10:30 AM 69.01 SP
4) To enter a title name, follow the steps of “Guide to
Edit Title Name” on page 87.
5) After entering a title name, press [OK].
6) Use [
K /L] to select “Yes”, then press [OK].
• The program name is now updated.