Panasonic PT-D12000U - Manual (Page 61)

ENGLISH – 61
Basic Operation
Adjusting the aspect ratio
This changes the aspect ratio of the projected image.
This changes the aspect ratio for the screen range
selected with “SCREEN SETTING”. Set “SCREEN
SETTING” first. (p. 72)
Press
▲▼ to select “ASPECT”.
1.
SHIFT
ASPECT
ZOOM
DEFAULT
Press
◄► or ENTER.
2.
The “ASPECT” individual adjustment screen •
will be displayed.
ASPECT
CHANGE
DEFAULT
Press
◄► to switch “ASPECT”.
3.
The setting will change as follows each time •
◄► is pressed.
VID AUTO (PRI.) DEFAULT
S1 AUTO THROUGH
VID AUTO 16:9
HV FIT 4:3
V FIT H FIT
DEFAULT: •
Pictures are displayed without changing the aspect
ratio of the input signals.
THROUGH:
•
Pictures are displayed without changing the
resolution of the input signals.
16:9:
•
When standard signals *1 are input, the pictures are
displayed with the aspect ratio converted to 16:9.
When wide signals are input
*2 , the pictures are
displayed without changing the aspect ratio.
4:3:
•
When standard signals are input *1 , the pictures are
displayed without changing the aspect ratio. When
wide signals are input
*2 , the PT-D12000U displays
pictures with the aspect ratio converted to 4:3. The
PT-DZ12000U displays pictures reduced to fit a 4:3
screen without changing the input aspect ratio.
H FIT:
•
The display will use the full width of the screen
range selected with “SCREEN SETTING”. When
signals have a vertical aspect ratio that is larger
than the screen aspect selected with “SCREEN
SETTING”, the pictures will be displayed with their
bottom areas cut off.
V FIT: •
The display will use the full height of the screen
range selected with “SCREEN SETTING”.
HV FIT: •
The pictures are displayed in the full screen range
selected with “SCREEN SETTING”. If the aspect
ratios of the input signals and screen range differ,
conversion to the screen aspect set with “SCREEN
SETTING” is performed and then the pictures are
displayed.
VID AUTO: •
The projector identifies the video ID (VID)
embedded in the picture signals and displays the
picture by automatically switching the screen sizes
between 4:3 and 16:9. This function is effective for
the NTSC signal input.
S1 AUTO: •
The projector identifies the S1 signal and displays
the picture by automatically switching the screen
sizes between 4:3 and 16:9. This function is
effective for S-Video NTSC signals.
VID AUTO (PRI.): •
The projector identifies the abovementioned VID or
S1 signals and displays the picture by automatically
choosing the screen sizes of 4:3 or 16:9 according
to the VID if it is detected or S1 signals if a VID is
not detected. This function is effective for S-Video
NTSC signals.
*1: Standard signals are input signals with an aspect
ratio of 4:3 or 5:4.
*2: Wide-screen signals are input signals with an
aspect ratio of 16:10, 16:9, 15:9 or 15:10.
Note
Some size modes are not available for certain types •
of input signals. For NTSC signals, “DEFAULT”
cannot be selected.
If an aspect ratio which is different from the aspect •
ratio for the input signals is selected, the pictures
will appear differently from the originals. Be careful
of this when selecting the aspect ratio.
If using this projector in places such as cafes or •
hotels to display programmes for a commercial
purpose or for public presentation, note that
adjusting the aspect ratio or using the zoom
function to change the screen pictures may be an
infringement of the rights of the original copyright
owner for that programme under copyright
protection laws.
If conventional (normal) 4:3 pictures which are •
not wide-screen pictures are displayed on a wide
screen, the edges of the pictures may not be visible
or they may become distorted. Such pictures
should be viewed as with an aspect ratio of 4:3 in
the original format intended by the creator of the
pictures.