Panasonic PT-D10000U - Manual (Page 79)

ENGLISH – 79
Special Features
The characters in the lamp selection menu will
become green when they are selected. Furthermore,
the characters may flash depending on the condition
of the lamps.
Yellow : An error has occurred with the illumination
of one or more of the lamps
White : Unselected item
Red : Lamp where an illumination error has
occurred
Lamp relay
If using the projector for a continuous period of
24 hours or more, this setting can be used to
automatically switch the lamps that are turned on in
order to reduce the lamp deterioration that can occur
as a result of continuous use.
“LAMP RELAY” will only be enabled when the lamp
selection is “SINGLE” (1 lamp), “DUAL” (2 lamps),
“TRIPLE” (3 lamps) or “QUAD” (4 lamps).
1. Press ▲▼ to select “LAMP
RELAY”.
2. Press ◄► to switch “LAMP
RELAY”.
The time interval for lamps to be switched will
change as shown in the diagram below each
time ◄► is pressed.
OFF 00:00
23:00 01:00
(Units of 1 hour)
Note
If the lamp selection is changed, picture is muted
during lamp switching execution. (7-25 sec.)
The lamps will switch at the specified time when the
lamp selection is “SINGLE” or “DUAL”.
When the lamp selection is “TRIPLE”, the lamps will
switch a total of three times at two-hour intervals
starting from the specified time, and after this the
previous operating status will be maintained until the
next specified time is reached.
•
•
•
•
•
•
OPTION2
PROJECTOR ID
INSTALLATION
ALTITUDE
DIRECTION
LAMP SELECT
LAMP RELAY
RS-232C
SYSTEM INFORMATION
AIR FILTER CLEANING
DATE AND TIME
STARTUP LOGO
PASSWORD
MENU SELECT
CHANGE
2
FRONT-F
LOW
H
QUAD
OFF
LOGO1
OPTION2
PROJECTOR ID
INSTALLATION
ALTITUDE
DIRECTION
LAMP SELECT
LAMP RELAY
RS-232C
SYSTEM INFORMATION
AIR FILTER CLEANING
DATE AND TIME
STARTUP LOGO
PASSWORD
MENU SELECT
CHANGE
2
FRONT-F
LOW
H
QUAD
OFF
LOGO1
When the lamp selection is “QUAD”, three lamps
will illuminate from the specified time, and the three
lamps will switch a total of four times at two-hour
intervals from that time. After this, four lamps will
illuminate for eight hours from the specified time,
and then when the next specified time is reached,
switching between three lamps will resume.
The setting time will be the local time. (p. 81)
RS-232C setting
This sets communication parameters for the projector.
1. Press ▲▼ to select “RS-232C”.
2. Press ENTER.
The “RS-232C” screen will be displayed.
3. Press ▲▼ to select “SERIAL IN”.
4. Press ◄► to switch “SERIAL IN”.
The setting will change as follows each time
◄► is pressed.
RS-232C RS-422
5. Press ▲▼ to select
communication conditions.
6. Press ◄► to confirm the setting.
7. Press MENU three times.
The on-screen indications disappear, and the
system returns to the normal screen.
•
•
•
•
•
OPTION2
PROJECTOR ID
INSTALLATION
ALTITUDE
DIRECTION
LAMP SELECT
LAMP RELAY
RS-232C
SYSTEM INFORMATION
AIR FILTER CLEANING
DATE AND TIME
STARTUP LOGO
PASSWORD
MENU SELECT
SUB MENU
2
FRONT-F
LOW
H
QUAD
OFF
LOGO1
ENTER
OPTION2
PROJECTOR ID
INSTALLATION
ALTITUDE
DIRECTION
LAMP SELECT
LAMP RELAY
RS-232C
SYSTEM INFORMATION
AIR FILTER CLEANING
DATE AND TIME
STARTUP LOGO
PASSWORD
MENU SELECT
SUB MENU
2
FRONT-F
LOW
H
QUAD
OFF
LOGO1
ENTER
RS-232C
SERIAL IN
(IN) BAUDRATE
(IN) PARITY
(OUT) BAUDRATE
(OUT) PARITY
VPS SYSTEM
GROUP
MENU SELECT
CHANGE
RS-232C
38400
EVEN
38400
EVEN
MASTER
A
MASTER
RS-232C
SERIAL IN
(IN) BAUDRATE
(IN) PARITY
(OUT) BAUDRATE
(OUT) PARITY
VPS SYSTEM
GROUP
MENU SELECT
CHANGE
RS-232C
38400
EVEN
38400
EVEN
MASTER
A
MASTER