Napco Security Technologies WI1501A - Manual (Page 23)

L
NAPCO Security Systems
Freedom F-64 Installation Instructions
WI1501A 9/06

Page 23
"ACTIVATE DIALER TEST Y/N" is displayed and then press YES to initiate the transmission of a Test Timer signal. Note: Test Timer
reporting codes and Report Test Timer on Telco1 or Telco 3 must be programmed. See glossary entry Test Timer.
Direct Address Program Mode See Dealer Program Mode
Disable Call Waiting (Touch-tone
® Dialing Only)
A digital communicator connected to a telephone line with Call Waiting may be disrupted by this feature. However, most lines with Call
Waiting also have Selective Call Waiting, which permits the feature to be turned off by dialing a "*70" just before the telephone number.
A "*" will be dialed by programming a "B".
If the installation has the Call Waiting feature, be sure that it also has Selective Call Waiting, and confirm the disable code with the
telephone company. Then program this code ("B70") directly before the phone numbers (after dial-tone detection or pre-dial delay) in
the telephone-number locations. See Telephone Numbers.
Caution: Should the user cancel his Call Waiting service, the communicator will dial a wrong number unless the phone number is
corrected.
Disable Call Waiting on 1
st Attempt
Cancel "*70" after the 1 st dial attempt. Default is disabled. When enabled, this option will dial the Central Station telephone number as it
is programmed in the panel. If the first communication is unsuccessful, the next and remaining dial attempts will remove the * star button
(entered as a "B" from the keypad) and the 2 subsequent digits from the Central Station telephone number.
Disable Callback Download See Callback-Method Download
Disable Code Required for Easy Bypass (Do not program for UL installations)
Any or all zones (1-64) programmed for Selective Bypass may be removed from the system, but each must be removed separately. Se-
curity Bypass, recommended for commercial applications, requires entry of a valid user code. Easy Bypass, recommended for residen-
tial applications, is selected by programming Disable Code Entry for Easy Bypass; this will permit bypassing/unbypassing zones without
the need of entering a code. Do not program this feature in high-security applications. Disable Code Required for Easy Bypass is
enabled by default.
Disable Function-Mode Download See Callback-Method Download, Touchpad Menu Mode
Disable Openings/Closings
Provides the flexibility of disabling openings and/or closings for any area(s).
Disable Handshake on Xmit (All Formats)
Causes data transmission to wait one second after dialing a pager telephone number before sending data.
Disable PGM2 Clear on Disarm
PGM2 will not clear when a user code or I-FOB is entered to disarm.
Disable System Trouble Audible Timeout
If the trouble occurs when disarmed, the sounder will now automatically time out in 10 minutes, without the need to press RESET.
(MUST be programmed in UL installations)
Disable Wait-for-Silence (Pager Format)
Causes data transmission to start immediately after the pager telephone number.
Disable Zone Fault Scrolling/Disable Auto Status
Non 24-Hour Zones that are open (or shorted) normally display "
ZONE FAULTS " (while disarmed) followed by the zone number(s) and
description(s). In high-security applications, program Disable Auto Status. Unsecured zones will then be indicated by a " ZONE
FAULTED " display without zone numbers displayed. Status may be displayed manually using the DISPLAY FAULTED ZONES function.
Double Reporting See Report Telco 3
"E" Lugs (E5, E15, E19) (Do not program for UL installations)
E5 - Lug E5 is used for Line Seizure. It is normally at 12V and when the telephone line is seized it goes to approximately 1V DC.
E15 - Lug E15 is used for Armed Status, either Armed Stay or Armed Away. When the system is armed it goes to approximately 1V
DC. For multiple area systems: If only 1 area, Lug E15 goes active low when area 1 is armed; if 4 areas, areas 1 through area 4
have to be armed for Lug E15 to go active low.
• Lug E15 Area 1 Armed Away Only: When enabled, Lug E15 will activate when area 1 is armed Away. Note: If this feature
is not selected, the E15 Lug will, by default, activate when the system is armed (all areas).
Glossar
y