Napco Security Technologies WI1501A - Manual (Page 25)

L
NAPCO Security Systems
Freedom F-64 Installation Instructions
WI1501A 9/06

Page 25
Enable Telephone Line Fault Test
Enable Line Fault Test will cause the panel to monitor the phone line. A failure will display as "
SYSTEM TROUBLE/E-08 SERVICE " for
Telco Line Fail. Program this system trouble to activate the Burglary Output.
Enable 2-Count Swinger Shutdown See Swinger Shutdown
Exit/Entry Delay; Exit/Entry 1; Exit/Entry 2; Entry Relay
Delays permit exit and entry through the Entry/Exit Zone(s) after the system is armed without setting off an immediate alarm. Entry delay
allows the user time to enter and disarm the panel. Exit delay allows the user to leave the premises after the panel has been armed.
Unless the keypad has been configured otherwise, the sounder will come on and will pulse during the last 10 seconds of entry delay to
remind the user to disarm.
Two individually-programmable entry-delay times are provided to accommodate different entry zones. If two or more Exit/Entry Zones
are entered in succession, the delay programmed for the last Exit/Entry Zone entered will take precedence over all others. Exit-Delay
time and Entry-Delay time may each be programmed for up to 255 seconds (4 minutes). See Time Selection.
An external relay may be programmed to trip upon entry (see Programming Manual: Relay Event ID Codes, Area Entry Relays), and
remain on for a programmed duration.
Note: In UL installations, maximum exit delay is 60 seconds; maximum entry delay is 45 seconds. In UL Mercantile installations, maxi-
mum entry delay is 60 seconds.
Entry delay may be canceled by pressing the
Q button prior to arming, however it will be restored automatically upon disarming.
Exit/Entry Follower
A zone programmed as an Exit/Entry Follower will ignore detection during the exit delay, and only during entry delay if the Exit/Entry
Zone is entered first. Thus, detection devices (passive infrared detectors, for example) along the path between the keypad and the exit/
entry door will not signal an alarm during exit/entry delay under normal conditions. However, if a device in the Exit/Entry Follower Zone
detects a violation when the exit/entry door has not first been entered, there will be no entry delay and the Exit/Entry Follower Zone will
go into an instant alarm. If the panel is armed with the entry delays canceled (Instant protection), any violation on the Exit/Entry Zone or
the Exit/Entry Follower Zone will cause an immediate alarm.
Exit Time Restart
This option allows for the following scenario prior to the end of the Exit Time: a violation of an entry/exit zone, a restore, and a second
violation of an entry/exit zone restarts the Exit Time. The panel does not allow the Exit Time to be restarted more than once. The default
setting for this option is enabled.
Expansion Module Zones; EZM Type; EZM Tamper See Tamper
Zones 9–64 or 17-64 (with "Zone Doubling" enabled) are expansion zones added to the basic system using expansion zone modules
(EZMs). Refer to the instructions accompanying each module for wiring information.
Each GEM-EZM4/8 Zone Expansion Module has series zone doubling and supervision capability. When an EZM is selected for zone
doubling, the EZM will respond as EZM 1 (zones 17 to 24) or EZM 3 (zones 25 to 32) when polled. (Refer to GEM-EZM4/8 Installation
Instructions). The EZM zone doubling or loop supervision functionality can be set to either follow the panel configuration or to act as a
standard non-zone doubled EZM. Program (see Programming Instructions WI1502) to enable all EZM's to follow the attributes of the
control panel (global panel feature). Note: A GEM-EZM8 cannot be used if the panel is set for loop supervision or zone doubling and
this feature is enabled.
Regardless of how the modules are arranged, the expansion zones are divided into consecutively-numbered groups of four. Each 8-
zone module comprises two groups. Each group is assigned a number.
EZ Arming (Easy Arming); Easy Arming Closing Report
Permits quick arming by simply pressing the
U
button on the F-64PROG programmer. Each keypad may be individually programmed
for Easy Arming (see Keypad Features). Disarming still requires entry of a valid user code. NOTE: Do not program in UL installations.
If closings are reported, Easy Arming will report as User 67. Press and hold
P or Q to EZ Arm using the F-64PROG program-
mer.
EZ Zone Doubling
The control panel zone configuration may be expanded from 8 to 16 zones without the use of EZM Modules. To do so simply select
"Zone Doubling" and connect zones as shown in Wiring Diagram. The 3.9K EOL resistor must be placed at the end of the loop of the
higher zone. For proper supervision, the 2.2K EOL resistor must be placed at the end of the loop of the lower zone.
Note: If Zone Doubling is to be used, then normally closed devices must be wired to both zones. If Normally open zones for fire or
panic devices are required, then the lower zone (2.2K EOL resistor) must be used and the higher zone (3.9K EOL resistor) must not be
programmed for any area.
Fire; Keypad Fire/Touchpad Fire
Any zone may be programmed for Fire. Connect normally-open devices across a Fire Zone. (The EOL2.2K end-of-line resistor must be
installed). A short across the zone will cause a fire alarm, which will be indicated at the keypad/Touchpad by a "
FIRE ALARM " LCD
Glossar
y