Nilfisk-Advance America Advenger BR 600S Series - Manual (Page 10)

A-10 - FORM NO. 56041554 - Advenger ™ , Advenger ™ AXP / BR 600S series
A-10 / ENGLISH
DETERGENT SYSTEM PREPARATION AND USE (AXP/EDS MODELS ONLY)
revised 3/06
COMMON INSTRUCTIONS:
The system should be purged of previous detergent when switching to a different
detergent. SERVICE NOTE: Move machine over fl oor drain before purging
because a small amount of detergent will be dispensed in the process.
To Purge When Changing Chemicals:
1
Disconnect and remove the detergent cartridge.
2 Turn the Key Switch (J) ON and press the Detergent ON/OFF Switch (S) and
the Flow Rate Switch (T) down for at least 3 seconds. NOTE: Once activated
the Flow Rate Indicator (U) will begin to fl ash and will automatically shut off
after 10 seconds. Normally one purge cycle is adequate to purge the system.
To Purge Weekly:
1
Disconnect and remove the detergent cartridge. Install and connect a
Cartridge fi lled with clean water
2 Turn the Key Switch (J) ON and press the Detergent ON/OFF Switch (S) and
the Flow Rate Switch (T) down for at least 3 seconds. NOTE: Once activated
the Flow Rate Indicator (U) will begin to fl ash and will automatically shut off
after 10 seconds. Normally one purge cycle is adequate to purge the system.
The Detergent Box (AA) has a Detergent Level Viewing Slot (BB) for keeping track
of how much detergent is remaining in the cartridge. When the detergent level is
nearing the bottom of this slot it is time to refi ll or replace the cartridge.
General Use:
The detergent (AXP/EDS) system is turned on when the Key Switch (J) is turned on
but no detergent is dispensed until the scrub system is activated and the Drive Pedal
(8) pushed forward. The solution fl ow rate automatically defaults to the last setting
used. The solution fl ow rate can be varied by subsequently pressing the Flow Rate
Switch (T). There are four solution fl ow rates indicated by the Flow Rate Indicator
(U). The detergent fl ow rate increases or decreases with the solution fl ow rate but
the detergent ratio remains the same. During scrubbing, the detergent system can
be turned off at any time by pressing the Detergent ON/OFF Switch (S) to allow
scrubbing with water only. The solution fl ow rate is controlled by the Flow Rate
Switch (T) whether the detergent system is ON or OFF.
SERVICE NOTE: Follow the “To Purge Weekly” instructions above if the machine is
going to be stored for an extended period of time or if you plan to discontinue use of
the detergent (AXP/EDS) system.
DISPOSABLE CARTRIDGE SPECIFIC INSTRUCTIONS:
Remove the Cap (CC) and place the cartridge in the detergent box. Install the Dry
Break Cap (DD) as shown.
NON-DISPOSABLE CARTRIDGE SPECIFIC INSTRUCTIONS:
Fill the detergent cartridge with a maximum of 1.25 gallons (4.73 Liters) of detergent.
SERVICE NOTE: Remove the detergent cartridge from the detergent box prior to
fi lling to avoid spilling detergent on the machine.
It is recommended that a separate cartridge be used for each detergent you plan
to use. The detergent cartridges have a white decal on them so you can write the
detergent name on each cartridge to avoid mixing them up. The detergent cartridge
has a Magnetic Slider (EE) on one end that needs to be set to the proper dilution
ratio according to the dilution instructions on the manufacturer’s bottle. Slide the
Magnet Slider (EE) to the appropriate location on Detergent Dilution Ratio Decal
(FF). When installing a new cartridge, remove the Cap (CC) and place the cartridge
in the detergent box. Install the Dry Break Cap (DD) as shown.