Radio Shack Weather Radio - Manual (Page 23)

23 Operation
Each time the outdoor wind chill temperature
changes and meets or drops below the set
temperature,
287 287 287 287
and the current readings
flash and the monitor sounds an alarm for
about 1 minute. To silence the alarm sooner,
press any key.
Note: If you press a key to silence the alarm,
the alarm stops sounding, but
287 287 287 287
and the
current readings continue to flash until the
alarm condition is no longer met.
1. Repeatedly press OUT until
''''(: (: (: (:
or
:,1' :,1' :,1' :,1' &+,// &+,// &+,// &+,//
appears.
2. Press ALARM .
$/$50 $/$50 $/$50 $/$50
appears when you
set the dew point temperature alarm, or
/2 /2 /2 /2 $/$50 $/$50 $/$50 $/$50
appears when you set the wind
chill temperature alarm.
3. Hold down SET until the dew point set-
ting or the current wind chill setting
flashes.
4. Repeatedly press (or hold down) or
to set the dew point or wind chill
alarm condition.
5. Press SET to store the setting.
Notes:
• If you do not press any button for about
60 seconds, the monitor returns to the
current temperature display. To continue
programming the settings, start over at
Step 2.
• You can only set the wind chill alarm on
the outside (
287 287 287 287
) channel.
Clearing the Outdoor Dew Point
or Wind Chill Temperature Alarm
Setting
To clear the dew point or wind chill alarm
conditions so the alarm does not sound,
repeatedly press
OUT until
'(::,1' '(::,1' '(::,1' '(::,1' &+,// &+,// &+,// &+,//
appears. Press ALARM , then press so


appears.
VIEWING AND RESETTING
MAX/MIN RELATIVE
HUMIDITY RECORDS
The weather station samples the indoor and
outdoor humidity and determines the relative
humidity percentage. The current indoor (
,1 ,1 ,1 ,1
)
and outdoor (
287 287 287 287
) relative humidity (
5+ 5+ 5+ 5+
)
conditions are located under the indoor and
outdoor temperature windows, respectively.
Note: You can also view the indoor relative
humidity from the indoor thermo/hygro/baro
sensor.
To view the maximum or minimum indoor or
outdoor relative humidity recorded since the
last memory reset, press the desired
%RH
(indoor or outdoor), then repeatedly press
0(025< 0(025< 0(025< 0(025<
until
0$; 0$; 0$; 0$;
or
0,1 0,1 0,1 0,1
appears. The record-
ed times of the maximum or minimum humid-
ity and
67$03 67$03 67$03 67$03
appear.
To reset the maximum or minimum relative
humidity records in memory and record a
new record (beginning with the current condi-
tion), hold down
0(025< 0(025< 0(025< 0(025<
for about 2 seconds
until the monitor beeps.
Using the HI/LOW Relative
Humidity Alarms
You can set the monitor to sound an alarm
when a set high or low indoor or outdoor rel-
ative humidity condition is reached.
Each time the relative humidity changes and
meets or exceeds an alarm condition,
+, +, +, +,
or
/2 /2 /2 /2
flashes, and the monitor sounds an alarm
for about 1 minute. To silence the alarm
sooner, press any key.
Note: If you press a key to silence the alarm,
the alarm stops sounding, but
+,/2 +,/2 +,/2 +,/2
and the
current readings continue to flash until that
alarm condition is no longer met.