Oregon Scientific DS6639 - Manual (Page 10)

ENGLISH
FRANÇAIS
ESP
AÑOL
DS6639 Manual-Eng/Fre/Span (086-003300-060)
ENGLISH
FRANÇAIS
ESP
AÑOL
14 15
Continue
Under this default option, the internal file counter is first set to “0001”. Every
subsequent picture is assigned an incremental File Number.
The internal file counter increments by 1 regardless of the media type,
unless it is reset.
New
Under this option, the internal file counter to “0001” for new media only. But in
case there are picture files already present inside the storage media, it will start
counting from the highest file number of the media.
It is advisable to set the File Number setting to New only in the
following cases:
• Either the internal memory or SD card has been newly formatted ( p.14).
• A completely new SD card has been installed.
Format
This option will format all data in either the
internal memory
or the external card
, including all protected image files.
Caution: Do not eject the SD card while the card
is being formatted, as this may damage the card.
Formatting deletes all data from the memory
device chosen. The images and files will not
be recoverable.
Reset
You can reset all the settings to factory default.
Refer to the Setup Menu table to see the
defaults for each setting (
p.11).
The reset function can reset all the
settings to factory default except for
the current time and date.
LCD Bright
You can adjust the LCD brightness level to
compensate for different lighting conditions,
for example.
• If there is plenty of ambient light such as in
bright sunshine, you can adjust the brightness
levels higher to make the display easier to see.
• If ambient light levels are relatively low such
as indoors or at night, you can adjust the brightness
levels lower to make the display easier to see.
TIP: To maximize battery life, keep brightness
settings low.
Info. (System Information)
This option allows you to check:
•
Camera model number.
• Current version of firmware installed.
Camera Menu Settings and Options
The options underlined and in italics are initial defaults.
Settings Page Options
Record Mode p.15 Camera or Movie mode Switch between digital still
selection and motion picture captures.
Size p.16 Super Fine 2048 (software-interpolated 3.0 Mega-Pixel) /
Fine 1600 (2.0 Mega-Pixel) / Normal 1280 (2.0 Mega-
Pixel) / Basic 640 (VGA)
Quality p.16 ECO (Economy) / STD (Standard) / HQ (High Quality)
White Bal p.17 Auto / Sunlight / Shade/ Yellow F.L. (Fluorescent Lamp)
/ White F.L. (Fluorescent Lamp) / Tungsten
Metering p.17 Central / Spot / Matrix
ISO p.18 Auto / 50 / 100 / 200
Con.Shoot p.18 Off / On
EV p.19 +2.0 / + 1.7 / +1.3 / +1.0 / +0.7 / +0.3 / 0.0 / -0.3/ -0.7 /
-1.0 / -1.3 / -1.7 / -2.0
Switching Between Camera and Movie Mode
Use the menu to switch between Camera and
Movie modes.
Movie Mode
In this mode you can record moving images at 10
frames per second. The duration of the movie will
depend on the battery life and memory available.
In Movie mode, you can only adjust the
white balance, EV and ISO. In Camera
mode, all settings will apply.
Camera Menu
3/4 Exit OK MENU
Cont
IN
Record
File No.
Format
Reset
LCD Bright
Setup
3/4 Exit OK MENU
Cont
IN
Record
File No.
Format
Reset
LCD Bright
Setup
1/2 Exit OK MENU
WB
AUTO
1600
H.Q.
Setup
Mode
Size
Quality
White Bal
Record
OK
Information
DS 6639
VER X.XXA