Toshiba DR420KU - Manual (Page 41)

41 EN 41 EN
Disc
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
Others
TIMER RECORDING
Hints for Timer Recording
PROG. A
PROG. B
actual
recording
PROG. A PROG. B
When the starting time is the same:
A program set previously (PROG. A) has priority.
The first 2 minutes (at the longest) will be cut off.
PROG. A
PROG. B
actual
recording
PROG. A PROG. A PROG. C PROG. B
PROG. C
When the starting time and the ending time
for each programs are different:
A program that has earlier start time has priority.
The first 2 minutes (at the longest) will be cut off.
PROG. A
PROG. B
actual
recording
PROG.B PROG.A
When the recording time is partially overlapped:
PROG. A will start after PROG. B is complete to
be recorded.
The first 2 minutes (at the longest) will be cut off.
PROG. A
PROG. B
actual
recording
PROG. B
When the recording time is entirely overlapped:
PROG.A will not be recorded.
This unit records the programs according to priority if the timer programmings are overlapped. The timer
programming set previously has priority.
A timer recording of lower priority will be canceled or start from the middle.
Check the overlapped timer programmings and change the priority if necessary.
• If there is a power failure or this unit has been
unplugged for more than 30 seconds, the clock setting
and all timer programming will be lost.
• If a disc is not inserted or if a inserted disc is not
recordable (finalized DVD-RW/-R, finalized DVD+RW, a
fully recorded disc, etc.),
on the front panel display
flashes and timer recording cannot be performed. In
some cases,
will appear momentarily around the start
point as the unit attempts to record. Please insert a
recordable disc.
• When all the timer recording is completed, flashes. To
play back or eject the recorded disc, press
[I/y ON/STANDBY] first, then select the recorded title and
press [PLAY B], or [OPEN/CLOSE A] to remove the disc.
• During timer recording or timer standby mode ( will
appear), any operations on the unit will not be available.
To make these operations available, press [STOP C] or
[C STOP] to stop the timer recording or
[I/y ON/STANDBY] to cancel timer standby mode (
will disappear).
• To cancel the timer standby mode, press
[I/y ON/STANDBY].
• When the starting and the ending time are the same,
“Exceeds 12 hours” appears and the program setting will
not be accepted.
• When the programmed starting and ending time are
earlier than the current time, the setting will not be
accepted.
• If the starting time is earlier and the ending time is later
than the current time, the recording will start right after
[I/y ON/STANDBY] is pressed.
• “Press ON/STANDBY for timer recording” will appear on
the TV screen 5 minutes before the programmed
starting time.
The Priority of Overlapped Settings
Note for DVD recording
• When the recording time of 2 programs are overlapped, or
the end time of a program and the start time of another
program is the same, the first 2 minutes (at the longest) of
the subsequent program will be cut off.
• If the cut-off portion comes up to 3 minutes or more, this
program will be displayed with errors number E40 in the
timer programming list.
PROG. A
PROG. B
actual
recording
The first 2 minutes (at the longest) will be cut off.
PROG. B PROG. A
When the end time of the programming
currently being recorded and the start time
of the subsequent program are same:
The beginning of the PROG. B may be cut off.
E7PCAUD_DR420KU_EN.indd 41 E7PCAUD_DR420KU_EN.indd 41 2/6/2009 10:55:34 AM 2/6/2009 10:55:34 AM