Toshiba RD-XS55KU - Manual (Page 149)

149
Other
s
Function setup
Librar
y
Editing
Pla
ybac
k
Recording
Intr
oduction
Netw
ork Na
vi
Default Gateway
DNS, DNS Server
Proxy Server
Proxy Port
MAC Address
Connection Check*
Note
• Please contact the router manufacturer when the router DHCP feature is not operating properly (in such a case, an error
will occur since the default gateway and the DNS server IP address cannot be obtained).
(Setting unnecessary)
Auto
Manual
Up to 63 single-byte
alphanumeric characters or
symbols
80
(Unable to set)
The default gateway that is obtained from the DHCP server is
displayed.
When “Use” is selected, the DNS server address is automatically
obtained from the DHCP server.
Manually enter the DNS server address.
Enter the proxy server address when your provider requires proxy
setting.
Normally there is no need to change this setting.
When required, change the value to a number between 1 and 65535.
The MAC address that is established for each recorder is displayed.
It cannot be changed.
This checks the connection between the recorder and the router.
* When “Connection Check” is pressed, items that were changed on the “Address/Proxy” and “Mail Setting” screens will be
saved, and you will not be able to return to the previous setting. Keeping a record of the setting is recommended as a
precaution.
Items for setting (Mail Setting screen)
Mail Function
Mail Keyword
POP3 Server Address
POP3 User Name
POP3 Password
APOP
Accept
From
Completion Notice
SMTP Server Address
Sender Address
Secondary Address
Disable
Enable
e.g.: rdstyle
e.g.: XXX.XXX.com
Enable
Disable
Only
All
e.g.:
[email protected]
Disable
Secondary Address
Return to sender
Secondary Address and
sender
e.g.: XXX.XXX.com
e.g.:
[email protected]
e.g.:
[email protected]
This will disable the use of the mail function.
This will enable the use of the mail function.
This sets 6-20 single-byte alphanumeric characters so that the email
for the mail function can be recognized. Symbols should not be
used since they will cause error and timer recording setting by email
will not be successful.
This sets the POP3 server address. (Enter up to 63 single-byte
alphanumeric characters.)
This sets the username for accessing the POP3 server. Enter up to
63 single-byte alphanumeric characters.
This sets the password for accessing the POP3 server. Enter up to
16 single-byte alphanumeric characters.
This enables the use of APOP (Authenticated POP*).
This disables the use of APOP (Authenticated POP*).
Only one email address is set as the sender.
No specific email address is set as the sender.
When “Accept” is set to “Only”, enter the email address of the
sender up to 63 single-byte alphanumeric characters.
Email notification is not sent when timer recording setting by email is
completed.
When timer recording setting by email is completed, notice is sent to
the completion-notice contact address.
When timer recording setting by email is completed, notice is sent to
the email sender’s address.
When timer recording setting by email function is completed, notice
is sent to both completion-notice contact address and the email
sender’s address.
This sets the SMTP server address.**
Enter up to 63 single-byte alphanumeric characters.
This sets the email address of your internet provider’s email service.
Enter up to 63 single-byte alphanumeric characters.
This sets the email address for sending notice when timer recording
setting by email is completed. Enter up to 63 single-byte
alphanumeric characters.
• Depending on the recorder’s operating mode, the timer recording setting may not be successful.
*
APOP: Password encrypting POP. For details, consult your ISP.
** The address of “POP3 Server Address” will be copied if you leave here blank.
RD-XS55SU_Ope_E_p141-170 06.3.20, 4:16 PM 149