White Rodgers 1F80-361 - Manual (Page 2)

2
Mounting
holes
Mounting
holes
Electric/Gas
switch
Screw anchors
INSTALLATION INSTALLATION INSTALLATION INSTALLATION INSTALLATION
REMOVE OLD THERMOSTAT REMOVE OLD THERMOSTAT REMOVE OLD THERMOSTAT REMOVE OLD THERMOSTAT REMOVE OLD THERMOSTAT
1. Shut off electricity at the main fuse box until installation is
complete. Ensure that electrical power is disconnected.
2. Remove the front cover of the old thermostat. With wires With wires With wires With wires With wires
still attached, still attached, still attached, still attached, still attached, remove wall plate from the wall. If the old
thermostat has a wall mounting plate, remove the thermo-
stat and the wall mounting plate as an assembly.
3. Identify each wire attached to the old thermostat using Identify each wire attached to the old thermostat using Identify each wire attached to the old thermostat using Identify each wire attached to the old thermostat using Identify each wire attached to the old thermostat using
the labels enclosed with the new thermostat.
the labels enclosed with the new thermostat. the labels enclosed with the new thermostat. the labels enclosed with the new thermostat. the labels enclosed with the new thermostat.
4. Disconnect the wires from old thermostat one at a time. DO DO DO DO DO
NOT LET WIRES FALL BACK INTO THE WALL. NOT LET WIRES FALL BACK INTO THE WALL. NOT LET WIRES FALL BACK INTO THE WALL. NOT LET WIRES FALL BACK INTO THE WALL. NOT LET WIRES FALL BACK INTO THE WALL.
5. Install new thermostat using the following procedures.
ATTENTION! ATTENTION! ATTENTION! ATTENTION! ATTENTION!
This product does not contain mercury. However, this product
may replace a unit which contains mercury.
Do not open mercury cells. If a cell becomes damaged, do not
touch any spilled mercury. Wearing nonabsorbent gloves, take
up the spilled mercury with sand or other absorbent material and
place into a container which can be sealed. If a cell becomes
damaged, the unit should be discarded.
Mercury must not be discarded in household trash. When the
unit this product is replacing is to be discarded, place in a
suitable container and return to White-Rodgers at 2895 Harrison
Street, Batesville, AR 72501 for proper disposal.
ELECTRIC HEAT OR SINGLE-STAGE ELECTRIC HEAT OR SINGLE-STAGE ELECTRIC HEAT OR SINGLE-STAGE ELECTRIC HEAT OR SINGLE-STAGE ELECTRIC HEAT OR SINGLE-STAGE
HEAT PUMP SYSTEMS HEAT PUMP SYSTEMS HEAT PUMP SYSTEMS HEAT PUMP SYSTEMS HEAT PUMP SYSTEMS
This thermostat is configured from the factory to operate a heat/
cool, fossil fuel (gas, oil, etc.), forced air system. It is configured
correctly for any system that DOES NOT require the thermostat
to energize the fan on a call for heat. If your system is an electric
heat or heat-pump system that REQUIRES the thermostat to
turn on the fan on a call for heat, locate the ELECTRIC/GAS
ELECTRIC/GAS ELECTRIC/GAS ELECTRIC/GAS ELECTRIC/GAS
switch switch switch switch switch on the back of the thermostat (see fig. 1) and switch it to
the ELECTRIC
ELECTRIC ELECTRIC ELECTRIC ELECTRIC position. This will allow the thermostat to
energize the fan immediately on a call for heat. If you are unsure
if the heating/cooling system requires the thermostat to control
the fan, contact a qualified heating and air conditioning service
person.
ATTACH THERMOSTAT BASE TO WALL ATTACH THERMOSTAT BASE TO WALL ATTACH THERMOSTAT BASE TO WALL ATTACH THERMOSTAT BASE TO WALL ATTACH THERMOSTAT BASE TO WALL
1. Remove the packing material from the thermostat. Gently
pull the cover straight off the base. Forcing or prying on the
thermostat will cause damage to the unit. If necessary, move
the electric heat switch (see ELECTRIC HEAT SYSTEMS
ELECTRIC HEAT SYSTEMS ELECTRIC HEAT SYSTEMS ELECTRIC HEAT SYSTEMS ELECTRIC HEAT SYSTEMS,
above).
2. Connect wires beneath terminal screws on base using
appropriate wiring schematic (see figs. 2 through 7).
3. Place base over hole in wall and mark mounting hole
locations on wall using base as a template.
4. Move base out of the way. Drill mounting holes.
5. Fasten base loosely to wall, as shown in fig. 1, using two
mounting screws. Place a level against bottom of base,
adjust until level, and then tighten screws. (Leveling is for
appearance only and will not affect thermostat operation.) If
you are using existing mounting holes, or if holes drilled are
too large and do not allow you to tighten base snugly, use
plastic screw anchors to secure subbase.
6. Push excess wire into wall and plug hole with a fire-resistant
material (such as fiberglass insulation) to prevent drafts
from affecting thermostat operation.
BATTERY LOCATION BATTERY LOCATION BATTERY LOCATION BATTERY LOCATION BATTERY LOCATION
2 "AA" alkaline batteries are included in the thermostat at the
factory with a battery tag to prevent power drainage. You must
You must You must You must You must
remove the battery tag to engage the batteries remove the battery tag to engage the batteries remove the battery tag to engage the batteries remove the battery tag to engage the batteries remove the battery tag to engage the batteries.
If “BATT” “BATT” “BATT” “BATT” “BATT” is displayed, the batteries are low and should be
replaced. For best results, replace all batteries with new pre-
mium brand alkaline batteries such as Duracell
® or Energizer ® .
To replace batteries, install the batteries along the top of the
base (see Fig. 1). The batteries must be installed with the
positive (+) end to the left.
HYDRONIC (HOT WATER OR STEAM) HYDRONIC (HOT WATER OR STEAM) HYDRONIC (HOT WATER OR STEAM) HYDRONIC (HOT WATER OR STEAM) HYDRONIC (HOT WATER OR STEAM)
HEATING SYSTEMS HEATING SYSTEMS HEATING SYSTEMS HEATING SYSTEMS HEATING SYSTEMS
This thermostat is set to operate properly with a forced-air
heating system. If you have a hydronic heating system (a
system that heats with hot water or steam), you must set the
thermostat to operate properly with your system. Change the
second option in the configuration menu to SL (see CONFIGU-
RATION MENU, page 4).
CHECK THERMOSTAT OPERATION CHECK THERMOSTAT OPERATION CHECK THERMOSTAT OPERATION CHECK THERMOSTAT OPERATION CHECK THERMOSTAT OPERATION
If at any time during testing your system does not operate
properly, contact a qualified service person.
Turn on power to the system.
Fan Operation Fan Operation Fan Operation Fan Operation Fan Operation
If your system does not does not does not does not does not have a G G G G G terminal connection, skip to
Heating System Heating System Heating System Heating System Heating System.
1. Move FAN switch to ON position. The blower should begin
to operate.
2. Move FAN switch to AUTO AUTO AUTO AUTO AUTO position. The blower should
stop immediately.
Figure 1. Thermostat Base Figure 1. Thermostat Base Figure 1. Thermostat Base Figure 1. Thermostat Base Figure 1. Thermostat Base