Operating features, Programming your thermostat – White Rodgers 1F80-361 User Manual

Page 5

Advertising

4) Select Energy Management Recovery OFF or ON

Select Energy Management Recovery OFF or ON

Select Energy Management Recovery OFF or ON -
Energy Management Recovery (EMR) causes the thermo-
stat to start heating or cooling early to make the building
temperature reach the program setpoint at the time you
specify. Heating will start 5 minutes early for every 1° of
temperature required to reach setpoint.

Example:

Example: You select EMR and have your heating pro-
grammed to 65° at night and 70° at 7 AM. If the building
temperature is 65° the difference between 65° and 70° is
5°. Allowing 5 minutes per degree the thermostat setpoint
will change to 70° at 6:35 AM. Cooling allows more time per
degree because it takes longer to reach temperature.

5) Select filter replacement run time

Select filter replacement run time

Select filter replacement run time - The thermostat will
display “FLTR”

“FLTR”

“FLTR” after a set time of operation. This is a

reminder to change or clean your air filter. This time can be
set from 0 to 1950 hours in 50 hour increments. A selection

A selection

of 000 will cancel this feature.

of 000 will cancel this feature. When “FLTR”

“FLTR”

“FLTR” is displayed,

you can clear it by pressing HOLD and RUN at the same
time. This resets the timer and starts counting the hours
until the next filter change. Changing the time in the menu
also resets the timer.

6) Select Compressor Lockout LOC OFF or ON

Select Compressor Lockout LOC OFF or ON

Select Compressor Lockout LOC OFF or ON - Selecting
LOC ON will cause the thermostat to wait 5 minutes before
turning on the compressor if the heating and cooling sys-
tem loses power. It will also wait 5 minutes minimum
between cooling cycles. This is intended to help protect the
compressor from short cycling. Some newer compressors
already have a time delay built in and do not require this
feature. Your compressor manufacturer can tell you if the
feature is already present in their system. When the com-
pressor time delay occurs it will flash the (snowflake icon)
for about five minutes then turn on the compressor.

7) Select Temperature Display Adjustment 4 LO to 4 HI

Select Temperature Display Adjustment 4 LO to 4 HI

Select Temperature Display Adjustment 4 LO to 4 HI -
Allows you to adjust the room temperature display 4° higher
or lower. Your thermostat was accurately calibrated at the
factory but you have the option to change the display
temperature to match your previous thermostat.

8) Select F° or C° Readout

Select F° or C° Readout

Select F° or C° Readout - Changes the display readout to
Centigrade or Fahrenheit as required.

OPERATING FEATURES

Now that you are familiar with the thermostat buttons and
display, read the following information to learn about the many
features of the thermostat.

• SIMULTANEOUS HEATING/COOLING PROGRAM

SIMULTANEOUS HEATING/COOLING PROGRAM

SIMULTANEOUS HEATING/COOLING PROGRAM
STORAGE

STORAGE

STORAGE — When programming, you can enter both
your heating and cooling programs at the same time. There
is no need to reprogram the thermostat at the beginning of
each season.

• TEMPERATURE OVERRIDE

TEMPERATURE OVERRIDE

TEMPERATURE OVERRIDE — Press

until the

display shows the temperature you want. The thermostat
will override current programming and keep the room
temperature at the selected temperature until the next
program period begins. Then the thermostat will automati-
cally revert to the program.

• HOLD TEMPERATURE

HOLD TEMPERATURE

HOLD TEMPERATURE — The thermostat can hold any
temperature within its range for an indefinite period without
reverting to the programmed temperature. Momentarily
press HOLD button. “HOLD”

“HOLD”

“HOLD” will be displayed. Then choose

the desired temperature by pressing

. The

thermostat will hold the room temperature at the selected
setting until you press RUN button to start program opera-
tion again.

• CONFIGURATION MENU

CONFIGURATION MENU

CONFIGURATION MENU — Allows you to customize
certain thermostat options.

PROGRAMMING YOUR THERMOSTAT

This section will help you plan your thermostat’s program to
meet your needs. For maximum comfort and efficiency, keep
the following guidelines in mind when planning your program.

• When heating (cooling) your building, program the

temperatures to be cooler (warmer) when the building is
vacant or during periods of low activity.

• During early morning hours, the need for cooling is

usually minimal.

Step

Press Button(s)

Displayed (Factory Default) Press or to select:

COMMENTS

HOLD

(0:00)

0 to 8 hrs (in

15 minute increments)

(FA)

Select temporary Hold time

(ON)

OFF

LOC

(OFF)

0 HI

(0)

4 LO to

4 HI

(F)

Returns to normal operation

Select Energy Management Recovery OFF or ON

Select compressor lockout OFF or ON

Select temperature display adjustment higher or lower

Select temperature display to F or C

RUN

PRGM

and RUN

HOLD

d-L

(ON)

OFF

Select display backlight OFF or ON

HOLD

Filter

(000)

0 to 1950 hours

(in 50 hour increments)

Select filter replacement run time

HOLD

Select FA or SL (Fast or Slow) heating cycle rate

Configuration Menu

* Press

HOLD to advance to next item or TIME to move backwards to previous item

Advertising

Popular Brands

Popular manuals