Festool CTL 36 E-LE-AC CLEANTEX - Manual (Page 16)

16
CLEANTEX CTL/ CTL AC GB
7.3 Adjusting the suction power
You can use the suction power adjuster [1-9]
to adapt the machine suction power to differ-
ent applications.
7.4 Applying the brake
Folding out the black brake lever [1-13] pre-
vents the mobile dust extractor from rolling.
To achieve this, lift the front end of the mo-
bile dust extractor slightly and push the
black brake lever downwards until it latches
into place. Push the green lever
[1-12] again
to release.
7.5 Temperature cut-out
To prevent overheating, a temperature cut-
out switches the mobile dust extractor off
when it reaches a critical temperature.
X Switch off the mobile dust extractor and
allow to cool for about 5 minutes.
L If the mobile dust extractor will not switch
on again, please contact a Festool service
workshop.
7.6 Changing the filter bag
Removing the filter bag [4]
X Open the locking clips [2-2] and remove
the top section of the machine [2-1] .
X Remove the filter bag.
X Dispose of the used filter bag in accor-
dance with statutory regulations.
X Clean the dust container [2-3] .
Inserting the filter bag [5]
X Insert a new filter bag (FIS-CT 26/36) in
the inlet port of the dust container and in-
terlock it. Important: be aware that the
locking engages.
X Replace the top section [2-1] and close
the locking clips [2-2] .
L Make sure that the filter bag is not
pinched between the top and bottom sec-
tions.
7.7 Changing the disposal bag
Removing the disposal bag [6]
X Open the locking clips [2-2] and remove
the top section of the machine [2-1] .
X Close the disposal bag.
X Remove the disposal bag.
X Dispose of the used disposal bag in accor-
dance with statutory regulations.
X Clean the dust container [2-3] .
Inserting the disposal bag [7]
X Insert a new disposal bag (ENS-CT26/36)
on the inlet nozzle of the container and
lock in position.
Important: The lateral openings on the
disposal bag must be positioned inside the
container. Make sure that the bolt engag-
es.
X Place the disposal bag over the edge of
the container.
Make sure that the contacts [10-2] are
free.
X Replace the top section [2-1] and close
the locking clips [2-2] .
8 Working
8.1 Handling
Hose store: after finishing work, you can
feed the suction hose through the recess
[8-
3] and place it in the hose store. You can do
the same with the mains cable through the
other recess
[8-2] .
SysDoc Systainer attachment system: a
Systainer can be attached to the storage
area via the two slides
[8-1] .
8.2 AUTO
Clean - Cleaning the main
filter (only versions with Auto-
Clean)
To maintain a constant suction power when
extracting fine dust, you can adjust the fre-
quency of the automatic
[1-7] cleaning sys-
tem in infinite variables using the rotary
knob. Always use the automatic cleaning
system in combination with a disposal bag
(in line with dust class 'L' requirements).
Before performing wet extraction tasks
or working with a filter bag, set the
[1-
7] rotary knob to position 0.
X Set the automatic cleaning function to the
highest setting when
[1-7] extracting
large quantities of dust.
Manual cleaning
If the suction power decreases, clean-
ing can be started manually by turning
the switch
[1-8] to the AC symbol po-
sitioned on either side of the switch.
We recommend cleaning the main filter
completely if severely clogged:
X Set the suction power adjuster [1-9] to
the maximum setting.
X Cover the end of the nozzle or suction
hose with your hand for 10 seconds.