Land of Nod OSLO CRIB - Manual (Page 4)

A
1
2
3
F
Carefully stand crib upright. This requires two people.
One person holds onto crib to prevent it from tipping over during
assembly step 6.
5
K.2
L.2
6
A
B
F
K.2 L.2
F
G
Line up other SIDE RAIL so its rail-connector-holes
align with the rail-connector-holes on the END PANELS .
Attach LOCKING WASHERS and REGULAR WASHERS
to RAIL CONNECTOR BOLTS and insert and tighten
the four RAIL CONNECTOR BOLTS with
ALLEN WRENCH as in steps 3 and 4.
Line up remaining SIDE RAIL so its rail-connector-holes align with the rail-connector-holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
Do not tighten all the way.
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
Do not tighten all the way.
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
G
F
G
B
4
A
L.2
K.2
L.2
K.2
3
Align second END RAIL to SIDE RAIL making sure that mattress support holes face the
bottom and inside of CRIB. Refer to diagram for proper orientation. Attach one LOCKING WASHER
and one REGULAR WASHER to two RAIL CONNECTOR BOLT and insert each RAIL
CONNECTOR BOLTS in rail connector holes and
slightly tighten with ALLEN WRENCH .
Do not tighten all the way.
Attach one LOCKING WASHER and one REGULAR WASHER to two RAIL CONNECTOR
BOLT and insert each RAIL CONNECTOR BOLTS in rail connector holes and
slightly
tighten with ALLEN WRENCH . Do not tighten all the way.
L.2
K.2
L.2
F