Land of Nod OSLO CRIB - Manual (Page 7)

A
1
2
3
F
Carefully stand crib upright. This requires two people.
One person holds onto crib to prevent it from tipping over during
assembly step 6.
5
K.2
L.2
6
A
B
F
K.2 L.2
F
G
Line up other SIDE RAIL so its rail-connector-holes
align with the rail-connector-holes on the END PANELS .
Attach LOCKING WASHERS and REGULAR WASHERS
to RAIL CONNECTOR BOLTS and insert and tighten
the four RAIL CONNECTOR BOLTS with
ALLEN WRENCH as in steps 3 and 4.
Line up remaining SIDE RAIL so its rail-connector-holes align with the rail-connector-holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
Do not tighten all the way.
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
Do not tighten all the way.
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Tighten all bolts with ALLEN WRENCH .
Flip crib rails over so top is on floor on a blanket or carpet. Place BASE on crib rails and secure
in place with ten BASE CONNECTOR BOLTS , LOCKING WASHERS , and REGULAR
WASHERS from underneath as shown below. Also, only slightly tighten bolts until all of them
are in place and aligned.
9
Attach X-FOOT to X-FOOT using notches to form X-frame. Place BASE on top of
X-frame. Attach each foot to corner bracket of base using RAIL CONNECTOR BOLTS ,
LOCKING WASHERS , and REGULAR WASHERS , and tighten with ALLEN WRENCH .
G
P
L.2
K.2
base connector holes