Land of Nod OSLO CRIB - Manual (Page 8)

A
1
2
3
F
Carefully stand crib upright. This requires two people.
One person holds onto crib to prevent it from tipping over during
assembly step 6.
5
K.2
L.2
6
A
B
F
K.2 L.2
F
G
Line up other SIDE RAIL so its rail-connector-holes
align with the rail-connector-holes on the END PANELS .
Attach LOCKING WASHERS and REGULAR WASHERS
to RAIL CONNECTOR BOLTS and insert and tighten
the four RAIL CONNECTOR BOLTS with
ALLEN WRENCH as in steps 3 and 4.
Line up remaining SIDE RAIL so its rail-connector-holes align with the rail-connector-holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
Do not tighten all the way.
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
Do not tighten all the way.
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
corner holes
C
11
The MATTRESS SUPPORT PANEL may be installed in one of four positions.
See the four different mattress support holes in each corner of the CRIB. First, select the
desired mattress height. Insert the smooth ends of each MATTRESS SUPPORT PIN in
the desired mattress support holes on SIDE RAILS .
See drawings for proper pin orientation.
10
Carefully lower MATTRESS SUPPORT PANEL with labels facing up.
Align corner holes to sit on MATTRESS SUPPORT PINS .
Tighten all RAIL CONNECTOR BOLTS on SIDE RAILS and END RAILS with
ALLEN WRENCH .