Land of Nod OSLO CRIB - Manual (Page 6)

A
1
2
3
F
Carefully stand crib upright. This requires two people.
One person holds onto crib to prevent it from tipping over during
assembly step 6.
5
K.2
L.2
6
A
B
F
K.2 L.2
F
G
Line up other SIDE RAIL so its rail-connector-holes
align with the rail-connector-holes on the END PANELS .
Attach LOCKING WASHERS and REGULAR WASHERS
to RAIL CONNECTOR BOLTS and insert and tighten
the four RAIL CONNECTOR BOLTS with
ALLEN WRENCH as in steps 3 and 4.
Line up remaining SIDE RAIL so its rail-connector-holes align with the rail-connector-holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
Do not tighten all the way.
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
Do not tighten all the way.
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
Line up remaining SIDE RAIL so its rail connector holes align with the rail connector holes on the
END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR
BOLTS and insert and
slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN
WRENCH as in steps 3 and 4. Do not tighten all the way.
6
1
2
3
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from
tipping over during assembly step 6.
7
It may be easier to access the top frame connector holes by laying the frame on its side (place on
a blanket to prevent scraping). Also, only
slightly tighten bolts until all of them are in place and
aligned. Tighten all bolts with ALLEN WRENCH .
Remove support bracket from TOP FRAME ASSEMBLY .
Place TOP FRAME ASSEMBLY on top of crib rails and secure in place with ten
CONNECTOR BOLTS , LOCKING WASHERS , and REGULAR WASHERS as
shown below. Place TOP FRAME RAIL on top of crib rails and secure in place with four
CONNECTOR BOLTS , LOCKING WASHERS , and REGULAR WASHERS
as shown below.
G
L.2
K.2
J
top frame
connector holes
top frame
connector holes
top frame
connector holes
M
L.2
remove support bracket