Uncle Milton Farm In My Room Wild Walls - Manual

5+
13274
SCENE SET-UP
Install the Wallscape FX Activator
TM
on your Wall
Before installing your Activator, move the function switch on the back
of the Activator from “Try Me” to “Play”. This will enable full special
effects functionality.
The Activator should only be mounted on a vertical surface.
For optimal results, place a nail or screw into the wall approximately
4 feet from the floor. Then, position the Activator onto the wall by
placing the hang hole on the back of activator directly over the nail
until securely in place.
Note: For rooms with ceilings higher than 8 feet, you may want to
position the activator higher than 4 feet to ensure that the light
sufficiently illuminates the wall and the ceiling.
Wall Decal Preparation
After removing the decals from the package, roll out the sheet and lay
flat for 24 – 48 hours until the sheet no longer wants to curl back up.
For best results apply the decals onto smooth, clean surfaces. The decals
may not stick to heavily textured surfaces. Do not apply to fresh paint or
wallpaper. Let the new paint/wallpaper dry for at least 3 weeks. Before
applying the decals to wallpaper or other delicate surfaces, test one in an
inconspicuous area. Keep the decals away from cribs and out of reach of
young children to prevent choking hazard.
Create your Scene by placing the Wall Decals
To apply each decal, carefully peel it off from the sheet. Then, place and
smooth the decal onto your wall in the desired location. To remove or
reposition each decal, just carefully peel it off from the wall. Kids can follow
the suggested scene layout or customize and create their own scene. For
optimal function with the light effects, please note the following suggestions
on wall decal placement:
• Begin with the lowest decal positioned 6” inches above the top of the
Activator.
• Then, place the bottom of the tractor decal approximately 15”
above the top of the Activator.
• Place all other decals around the featured animal decal but ideally no more
than 36 inches above the top of the Activator. This will help to
ensure that all decals are illuminated by the light cast.
On textured walls, periodically check the decals to make sure they are remaining flat
against the surface. Gently smooth any parts of the decal, that appear to be lifting off the
surface. Repeat as needed until the decals remain flat against the surface.
SCENE ACTIVATION
Now you can activate your scene using different programming modes on the
Wallscape FX Activator as follows:
TRY ME (10 second demo)
This is the factory default program and is used for in store demonstration. It is not
intended for home use and has limited functionality. For full functionality, move the
function switch on the back of the Wallscape FX Activator from “Try Me” to “Play”.
MODE 1 – FULL FUNCTIONALITY LIGHT & SOUND SHOW
Press the program button once to activate. This will enable full light
and sound special effects including the following:
• Music and undersea sound effects
• Light gently fading in and out, illuminating your wall and ceiling
• Synchronized lights and sounds that bring the scene to life.
In this mode, auto shut-off of the sound will occur approximately after 5 minutes
and auto shut-off of the light will occur approximately after 10 minutes.
MODE 2 – LIGHT SHOW ONLY
Press the program button two times to activate. This will enable full light functionality
but will not include any sound effects. Auto shut-off will occur approximately after
20 minutes.
MANUAL SHUT-OFF
To manually turn off the Wallscape FX Activator, press and hold down the program
button for approximately two seconds until the light and sound turns off.
BATTERY REPLACEMENT
Tool required - Small Phillips head screwdriver
Requires 3 AA/LR6 alkaline batteries.
1. Using a Phillips head screwdriver, remove the battery cover.
2. Insert 3 AA/LR6 alkaline batteries as indicated in the battery
compartment and replace cover.
3. IMPORTANT! Switch the Wallscape FX Activator to the PLAY
position before hanging on the wall.
2
1
3
4
DO NOT SKIP THIS STEP
Farm in My Room Farm in My Room Farm in My Room Farm in My Room
Instruction Manual
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE — DO NOT DISCARD
Questions? Visit unclemilton.com
Function
Switch
Hang
Hole
Battery
Cover TRY ME
PLAY
Wallscape FX Activator
TM
Wallscape FX Activator
TM
Scene Set-Up Scene Set-Up
6” inches
15”
inches
36” inches
Top of Wallscape
FX Activator
PRODUCT STYLES
MAY VARY
Floor
4 Feet