Velleman VDP2301RGVLD10 - Manual (Page 10)

VDP2301RGVLD10 - VDP2601RGYLD10 - VDP3801RGVLD10
11/08/2011 ©Velleman nv 10
• Click on No File to remove the file from the list.
• Click OK to save the settings.
• When desired, a list of all DMX settings can be printed by clicking the Print button.
• To save the configuration, click on Save Config. The file must be saved as CONFIG.DAT as this is the
file that will be loaded automatically by the laser projector.
• Place the SD card back in the laser projector and switch the projector on. Make sure the SD CARD mode
switch [6] is pressed and the correct DMX address is set via the SD card controls.
6.3 PC controlled mode
• The PC controlled mode uses the ILDA (International Laser Display Association) standard for control signal
and file formats. The laser projector must be connected to a suitable PC running appropriate software (e.g.
Pangolin, Mamba, Phoenix…). Refer to §5 for the cable layout of the ILDA cable. More on the ILDA standard
can be found on http://www.laserist.org/standards.htm .
IMPORTANT NOTE
Make sure to set the scan rate in the software equal to or lower than the actual scan rate of
the laser projector. Setting the scan rate too high may damage the laser projector; this
damage is not covered by the warranty.
• Press the PC MODE switch [6] to select PC mode.
• In this mode, the laser projector will receive its instructions and shows via the ILDA input port [10].
• Multiple laser projectors can be linked via the ILDA THRU port [9].
7. Cleaning and Maintenance
• All screws should be tightened and free of corrosion.
• The housing, visible parts, mounting supports and the installation location (e.g. ceiling, suspension,
trussing) should not be deformed, modified or tampered with e.g. do not drill extra holes in mounting
supports, do not change the location of the connections.
• Moving mechanic parts must not show any signs of wear and tear.
• The electric power supply cables must not show any damage. Have a qualified technician maintain the
device.
• Disconnect the device from the mains prior to maintenance activities.
• Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.
• There are no user-serviceable parts apart from the fuse.
• Contact your dealer for spare parts if necessary.
8. Technical specifications
VDP2301RGVLD10 VDP3801RGVLD10 VDP2601RGYLD10
Laser colour
/power
red 663nm/160mW 665nm/215mW 662nm/200mW
green 533nm/100mW 533nm/85mW 533nm/100mW
purple 408nm/200mW 405nm/200mW -
max. total output power 460mW 500mW 300mW
max. scan speed 20 Kpps 20 Kpps 20 Kpps
optical angle ±20° ±20° ±20°
Power supply AC 110-240V 50/60Hz
Power consumption 300W
Dimensions 200 x 260 x 450mm 200 x 260 x 310mm
Total Weight 7.0kg ±5.5kg
Laser type DPSSL (Diode Pumped Solid State Laser) green: DPSSL
red: semiconductor laser diode
Laser class Class 3B
Laser life >5000h
Use this device with original accessories only. Velleman nv cannot be held responsible in the event
of damage or injury resulted from (incorrect) use of this device. For more info concerning this
product and the latest version of this user manual, please visit our website www.hqpower.eu. The
information in this manual is subject to change without prior notice.
© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman nv. All worldwide rights reserved.
No part of this manual or may be copied, reproduced, translated or reduced to any electronic medium or otherwise without
the prior written consent of the copyright holder.