Mounting instructions, Removing and installing the i/o board or, Blank panel – Extron Electronics DMS 1600_2000_3200_3600 User Guide User Manual

Page 107

Advertising
background image

DMS 1600, DMS 2000, DMS 3200, and DMS 3600 • Maintenance and Modifications 101

Removing and Installing the I/O Board or Blank Panel

NOTE: For proper cooling and air flow, install boards or blank panels in all locations.

Figure 67 shows a mix of I/O boards. On the boards, the input and output DVI connectors
are identified as A through D. Each I/O board is identified by the input and output numbers
supported by the board position (1 - 4, 5 - 8, and so on).

ANAHEIM, CA

100-240V 50/60Hz 1.2A MAX.

PRIMARY POWER SUPPLY

REDUNDANT POWER SUPPLY

1 - 4

5 - 8

9 - 12

13 - 16

A

B

DVI-D INPUTS

DVI-D OUTPUTS

C

D

A

B

C

D

DVI-D OUTPUTS

A

B

C

D

A

B

TMDS
FIBER

INPUTS

C

D

A

B

TMDS
FIBER

OUTPUTS

DMS FIBER 44

C

D

Location A
Input

Location D
Output

Location D
Output

Location A
Input

Input 1

Slot 1

(1-4) Input/Output

Board

Slot 2

(5-8) Input/Output

Board

Slot 4

No board installed

Slot 3

(9-12) Output Board

Input 2

Input 3

Input 4

Input 5

Input 6

Input 7

Input 8

Output 9

Output 10

Output 11

Output 12

Output 1 Output 2 Output 3

Output 4

Figure 67.

Arrangement of Inputs and Outputs on the I/O Boards

Slot

Inputs and outputs

Slot

Inputs and outputs

1

1 through 4

5*

17 through 20

2

5 through 8

6

21 through 24

3

9 through 12

7

25 through 28

4

13 through 16

8

29 through 32

9

33 through 36

* DMS 2000, DMS 3200, and DMS 3600 only

DMS 3200 and DMS 3600 only

DMS 3600 only

Locations A through D correspond to the input and output numbers identified by the board
position numbers. (For example, the input and output numbers supported by the I/O board
in slot 2 (location 5 - 8) are as follows: A = 5, B = 6, C = 7, and D = 8.) Inputs and outputs
are grouped separately, with inputs A through D on the left and outputs A through D on the
right.
Below are installation guidelines for the switcher configuration; if you incorrectly order the
I/O boards, the switcher will not recognize some inputs, outputs, or both.

•

You

must install a 4x4 DVI or fiber optic input and output board in the top slot (slot 1).

•

You can install any of the six board types (a 4x4 DVI or fiber optic input and output
board, a 4 DVI or fiber optic input board, or a 4 DVI or fiber optic output board) or a
blank panel in the next slot (slot 2).

•

You can install any of the board types in the slot directly underneath a 4x4 input and
output board.

•

After you install a 4-input board or 4-output board, all active boards underneath it

must

be the same size (4-input or 4-output).

•

Within these size guidelines (4-input must follow 4-input or 4-output must follow
4-output), you can follow a DVI board with a fiber optic board or follow a fiber optic
board with a DVI board.

•

If you install a blank panel, all slots under it

must contain blank panels (you cannot skip

a slot).

Advertising