Reset button – Extron Electronics HDXP Plus Series User Guide User Manual

Page 15

Advertising
background image

HDXP Plus Series Switchers • Installation

9

Figure 6 shows a configuration in which the timing source passes through three video
cameras and a video scan converter before connecting to the switcher. This type of
camera can synchronize with the external timing source for video editing applications.

NOTE: I/O grouping is used to set the inputs associated with each reference

input. Input group 1 is associated with the tri-level signal and input group 2 is
associated with the bi-level signal.

Extron
BBG 6 A

Blackburst/Color Bars/
Audio Generator

I
N

P
U

T
S

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

O

U

T
P
U

T
S

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

2

3

4

21

6

7

8

25

10

11

12

29

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

LA

N

AC

T

LINK

BI-LEVEL

RESET

TRI-LEVEL

GEN-L

OCK

PREVI

EW

50/

60 H

z

100

-24

0V

0.3

A

R

/R-

Y

R

/R-

Y

I
N
P
U
T
S

O
U
T
P
U
T
S

G

/Y

2

RG

B/R

-Y,

B-Y

, Y

RG

B

1

G-Y

B

/B-

Y

B

/B-

Y

H

/HV

H

/HV

V

V

VID

EO

S-VIDEO

D1

R/R

-Y

G/Y

B/B

-Y

H/H

-Y

RS

-23

2

/42

2

G

E

N

L

O

C

K

V

IN

OU

T

SDI/HD-SDI
Video Camera

SDI/HD-SDI
Monitor

Extron
HDXP Plus 3232

Matrix Switcher

SDI/HD-SDI
Video Camera

SDI/HD-SDI
Video Camera

VGA Input

Extron
VSC 900D

Computer-to-Video
Scan Converter
(SDI only)

DISTRIB

UTIO

N AM

PLIFIER

Figure 6.

Multiple Device Example of an HDXP 3232 External Sync

If no external sync timing source is connected, switching occurs immediately.

Reset Button

e

Reset button — This recessed button initiates three levels of reset on the matrix
switcher. To initiate the different levels of reset, use a pointed object such as a stylus
or a small screwdriver to press and hold the Reset button while the switcher is
running or while you are powering it up (see

Resetting

on page 37 for details).

•

Events (mode 3) reset — Hold the Reset button until the Reset LED blinks
once (approximately 3 seconds), then release it and press it again momentarily to
toggle events monitoring on and off.

•

IP settings (mode 4) reset — Hold the Reset button until the Reset LED blinks
twice (approximately 6 seconds), then release it and press it again to reset the
switcher IP functions.

NOTE: IP settings reset does not replace any user-installed firmware.

Absolute (mode 5) reset — Hold the Reset button until the Reset LED blinks
three times (approximately 9 seconds), then release it and press it again to restore
the switcher to the default factory settings.

•

Hard reset — Hold the Reset button while powering up the switcher to restore
the switcher to the default factory settings and factory installed firmware version.

NOTE: This type of reset does not clear the current configuration.

Advertising