Atec Kepco-KLP Series - Manual (Page 2)

KLP MODEL TABLE
MODEL (3)
RATED
VOLTAGE
RANGE
(1)
MAXIMUM
CURRENT
FOR RATED
VOLTAGE
MAXIMUM
VOLTAGE
FOR RATED
CURRENT
RIPPLE
AND
NOISE (2)
p-p
EFFICIENCY
@
115V a-c
MINIMUM
PROGRAMMABLE
CURRENT
RATED
CURRENT
RANGE
(1)
KLP 10-150
KLP 20-120
KLP 36-60
KLP 75-33
KLP 150-16
KLP 300-8
KLP 600-4
0-10V
0-20V
0-36V
0-75V
0-150V
0-300V
0-600V
60 mV
60 mV
60 mV
60 mV
125 mV
150 mV
150 mV
80%
82%
83%
84%
86%
87%
88%
120A@10V
60A@20V
33.3A@36V
16A@75V
8A@150V
4A@300V
2A@600V
1.9A
1.5A
0.8A
0.4A
0.2A
0.1A
0.05A
0-150A
0-120A
0-60A
0-33.3A
0-16A
0-8A
0-4A
8V@150A
10V@120A
20V@60A
[email protected]
75V@16A
150V@8A
300V@4A
(1) The maximum current and voltage are constrained by the 1200 watt power limitation.
(2) Bandwidth: 20MHz; low frequency ripple may be higher at loads less than 30 Watts.
(3) Standard models (no suffix) include built-in GPIB and RS-232 interfaces.
E-series models (Suffix E) include built-in GPIB and LAN interfaces.
KLR MODEL TABLE
MODEL(1)
RATED
VOLTAGE
RANGE
RIPPLE AND
NOISE (2)
p-p
EFFICIENCY
@
230V a-c
MINIMUM
PROGRAMMABLE
CURRENT
RATED
CURRENT
RANGE
KLR 20-120
KLR 40-60
KLR 75-32
KLR 150-16
KLR 300-8
0-20V
0-40V
0-75V
0-150V
0-300V
100 mV
80 mV
80 mV
100 mV
150 mV
87%
88%
87%
88%
89%
1.5A
0.8A
0.4A
0.2A
0.1A
0-120A
0-60A
0-32A
0-16A
0-8A
(1) Standard models (no suffix) include built-in GPIB and RS-232 interfaces.
E-series models (Suffix E) include built-in GPIB and LAN interfaces.
(2) Bandwidth: 20MHz; low frequency ripple may be higher at loads less than 30 Watts.
Data subject to change without notice.
© 2013 KEPCO, INC. Litho in USA
KEPCO, INC. • 131-38 Sanford Avenue • Flushing, NY 11355 USA • Tel: (718) 461-7000 • Fax: (718) 767-1102
Email: [email protected] • www.kepcopower.com
B
C
A
CONVENTIONAL
POWER SUPPLY’S
MAXIMUM
POWER POINT
ADDITIONAL
OPERATING
REGION
CONVENTIONAL
OPERATING REGION
ADDITIONAL
OPERATING
REGION
KEPCO KLP’S
1200 WATT
EXTENDED
MAXIMUM
POWER
RANGE
“A” THRU “C”
16 0 33
36
75
V
O
LT
S
AMPERES
I
V
KEPCO SERIES KLP
KEPCO SERIES KLR
Using high-frequency switch-mode topology for high
efficiency and small size, the KLP provides 1200 watts
of well-regulated, controllable d-c power in a 1U
(1.75 inch high) by 19 inch rack-mountable package.
KLP replaces the need for multiple power supplies
by expanding the operating region. The breakthrough
of a hyperbolic power limit delivers a full 1200 Watts
over an expanded operating range, not just the
conventional rectangular operating area.
www.kepcopower.com/klp.htm
Kepco introduces Series KLR, offering 2400 Watts
of stable, controllable d-c power in the industry
standard 1U package. Five models from 20 Volts to
300 Volts are available with a conventional rectangular
operating area. Input is 180-264V a-c, single phase.
GPIB, RS232 and isolated analog programming are
all standard.
www.kepcopower.com/klr.htm