Atec Kepco-KLP Series - Manual (Page 4)

KEPCO, INC. • 131-38 Sanford Avenue • Flushing, NY 11355 USA
Tel: (718) 461-7000 • Fax: (718) 767-1102
Email: [email protected] • www.kepcopower.com
KLP/KLR OUTPUT CHARACTERISTICS
SPECIFICATION RATING/DESCRIPTION CONDITION
Stabilizer Type CV/CC Voltage/Current
Adjustment
Range 0-100% of rated voltage
No minimum
load required
Voltage
min-100% of rated current (1) Current
Source Effect 0.01% E
max Over full
source range
Voltage
0.01% l
max
Current
Load Effect 0.02% E
max Over full
rated load
Voltage
0.05% l
max
Current
Temperature
Effect 0.01%/ ºC
0.01%/ ºC
0-50ºC Voltage
Current
Time Effect
(drift) 0.02%/24hr
After 30 minute
warmup
Voltage
0.02%/24hr Current
Error Sensing 0.25 volts per wire Above rated output
Rated output, any load
Transient
Recovery
for Load
Change 1% of E
max
50% load step 2A/
microsecond max
Excursion
2 msec 10% min load, Return
to 0.1% of setting
Recovery
Turnon/turnoff
Overshoot 2% max
Overvoltage
Protection Programmable
20-120% of E
max
User selectable
recovery (3)
Overcurrent
Protection Programmable
72-120% of I
max
User selectable
recovery (3)
Output Load
Wire Protection Shutdown
Parallel Operation Active load sharing within
5% of I
0
rated
User selectable
recovery (3)
Up to 5 units
maximum (4)
Rise Time 10 - 40V: 30 msec
75V: 40 msec
150V: 50 msec
300V: 60 msec
600V: 75 msec
0-E
max
rated load
(resistive)
Voltage
10 - 40V: 30 msec
75V: 40 msec
150V: 50 msec
300V: 60 msec
600V: 75 msec
0-I
max
rated load
(resistive)
Current
10 - 40V: 30 msec
75V: 40 msec
150V: 50 msec
300V: 60 msec
600V: 75 msec
I
max
-0
rated load
(resistive)
Current
Fall Time 10V: 475 msec
20V: 525 msec
36V: 825 msec
40V: 975 msec
75V: 2820 msec
150V: 4850 msec
300V: 4400 msec
600V: 3150 msec
E
max
-0, no load
(open circuit)
Voltage
No Load (2)
10 - 40V: 30 msec
75V: 40 msec
150V: 50 msec
300V: 60 msec
600V: 75 msec
E
max
-0
rated load
(resistive)
Voltage
Rated Load
(1) See Model Table for minimum programmable current.
(2) For improved fall time performance consult factory for "R" (Rapid Output
Discharge) option.
(3) Either PROTECTED (output disabled and locked until source power
recycled) or SAFE (output disabled with unit programmed to last setting;
power recycling not needed for recovery).
(4) E-series are not Master/Slave capable.
Isolation
Voltage 10-40V: 100V d-c or peak
75-600V: 600V d-c or peak
Either output
terminal to ground
KLP/KLR PHYSICAL SPECIFICATIONS
SPECIFICATION RATING/DESCRIPTION CONDITION
Weight English 15 lbs Shipping: 20 lbs
Metric 6.82 Kg Shipping: 9.07 Kg
Dimensions English 19" x 1.735" x 17.5" Depth excluding
W x H x D
Metric 482.6mm x 44.45mm
connectors and
x 443.7mm
terminal blocks
Source Power IEC 320-C19 250V a-c,
Connector appliance inlet 16A (VDE)
125V a-c,
20A (UL)
Load 10-40V Nickel-plated copper Provision for
Connections models busbar with integral safety covers
threaded stud
(1/4-20-1/2in.)
75-600V Shock-safe Euroblock,
models single conductor size:
20-10 AWG
(0,5-5,0 mm 2 )
Analog 15 pin D-sub
Programming Port
Digital Primary Standard GPIB IEEE 488.2 (GPIB)
Programming connector
Ports
Secondary 9 pin D-sub RS 232 (standard
models only)
Secondary RJ45 LAN (E-Series
models only)
Feedback/ 5 position low profile
Control Input Euroblocks
(1) Either PROTECTED (output disabled and locked until source power
recycled) or SAFE (output disabled with unit programmed to last setting;
power recycling not needed for recovery) or AUTO (when fault clears,
unit automatically recovers to programming setpoints and output state
(enabled/disabled) as before fault was detected.
KLP/KLR GENERAL SPECIFICATIONS
SPECIFICATION RATING/DESCRIPTION CONDITION
Temperature Operating -10 to +50°C Rated load
+50 to +70°C Derate current 3%
per °C over 50°C
Storage -40 to +85°C
Cooling 3 internal d-c fans Exhaust to the rear
Humidity 10 to 90% RH Non-condensing
Shock 20g, 11msec ± 50% Non-operating
half sine
Vibration 5-10Hz 10mm double amplitude 3-axes, non-operating
10-55 Hz 2g 3-axes, non-operating
Altitude sea level to 10,000 ft. 0-3,000 ft: 100%,
linear derating
to 70% of power
at 10,000 ft.
Loss of Shutdown User selectable
Source Power recovery (1)
Overtemperature Shutdown User selectable
Protection recovery (1)
Fan Failure Shutdown Recovery requires
power recycling
Withstand Input- 2121V d-c 25°C, 65% RH
Voltage Chassis (all models)
Output- 1250V d-c
Chassis (10V-40V models)
2121V d-c
(75V-600V models)
Input- 2500V d-c
Output (10V-40V models)
4242V d-c
(75V-600V models)