Atec Kepco-KLP Series - Manual (Page 3)

FEATURES
KLP: Provides 1200W output power over a hyperbolic output power envelope,
resulting in full output power availability over the range of 8V, 150A to 600V, 2A
KLR: Provides up to 2400W output power via a conventional rectangular output
power envelope, resulting in full output power at model limits only
Switch mode topology for cool, efficient operation
GPIB and isolated analog programming included on all models
Standard models have an RS-232 interface
E-Series models replace the RS-232 interface with an Ethernet (RJ-45) connector
supporting LAN (LXI certified for KLP)
KLP: 1U panel height at 1200 watts
KLR: 1U panel height at 2400 watts
Front to back air flow allows full power operation without spacers between supplies
KLP: Operates over universal a-c mains voltage range of 90 - 264V a-c with PFC
KLR: Operates over a-c mains voltage range of 180 - 264V a-c with PFC
KLP: Stud-style output power terminals for LV models (10V, 20V, 36V), and
Euroblock output power terminals for HV models (75V, 150V, 300V, 600V)
KLR: Stud-style output power terminals for LV models (20V, 40V), and
Euroblock output power terminals for HV models (75V, 150V, 300V)
KEPCO, INC. • 131-38 Sanford Avenue • Flushing, NY 11355 USA • Tel: (718) 461-7000 • Fax: (718) 767-1102
Email: [email protected] • www.kepcopower.com
KLP/KLR INPUT SPECIFICATIONS
SPECIFICATION RATING/DESCRIPTION CONDITION
SERIES KLP SERIES KLR
a-c Voltage Nominal 100-240V a-c 200-240V a-c Single phase
Range 90-265V a-c 180-265V a-c Wide range
Input Nominal Range 50-60 Hz 50-60 Hz
Frequency
Maximum 45-440 Hz 45-440 Hz Increased leakage above 66 Hz
Power Factor (PF) Typical 0.99 0.99 Meets EN 61000-3-2
Maximum 120V a-c 13A rms N/A Rated load (1200W)
Input Current
240V a-c 6.5A rms N/A Rated load (1200W)
230V a-c N/A 12A rms Rated load (2400W)
Inrush Current 265V a-c 40A 40A Peak
132V a-c 20A N/A Peak
Input Fusing Circuit breaker Circuit breaker 2-line
Low a-c Protection 87V a-c self protected 175V a-c self protected User-selectable recovery (1)
Output Holdup Typical 10 milliseconds 5 milliseconds Ride through
Leakage 115V a-c, 60 Hz 1.2mA max N/A
Current
230V a-c, 50 Hz 2.3mA max 2.3mA max
(1) Either PROTECTED (output disabled and locked until source power recycled) or SAFE (output disabled with unit programmed to last setting; power recycling
not needed for recovery) or AUTO (when fault clears, unit automatically recovers to programming setpoints and output state (enabled/disabled) as before fault
was detected.
NOTE: Contact Kepco Applications Engineering for d-c input.
MARKETS AND APPLICATIONS
• Aerospace and Satellite Test
• Telecom and IT Industry
• Automated Test Equipment
• Factory Automation
• QC Testing
• Burn-in
• Solar
• Water Purification
• Thermal Process Control
• Chemical Processing
• Semiconductor Manufacturing
• Battery Charging and Testing
• Electroplating, Sputtering and Coating
• New Energy R&D