American Dynamics RAS916WLS - Manual (Page 76)

VM32/AD32
Supported Protocols SensorNet
RS-422
(1)
Maximum Presets 96 – SensorNet
4 – RS-422
Maximum Patterns
(2)
3
Quick Set Menu Not supported
Address Range 1-32
Notes:
(1) Requires RCSN422 code converter.
(2) Patterns are limited by time and the number of
available dome commands. Total time for each
pattern cannot exceed 6 minutes 50 seconds.
Total dome commands used in all patterns cannot
exceed 99.
VM96 (1)
Supported Protocols SensorNet
RS-422
Maximum Presets Unlimited
(2)
Maximum Patterns
(3) 3
Quick Set Menu Not supported
Address Range 1-96
Notes:
(1) Requires software version 5.2 or newer.
(2) Preset information is stored at the host, not the
dome.
(3) Patterns are limited by time and the number of
available dome commands. Total time for each
pattern cannot exceed 6 minutes 50 seconds.
Total dome commands used in all patterns cannot
exceed 99.
AD2150/AD2350
Supported Protocol RS-422
(1)
Maximum Presets 16
(2)
or 60
(3)
Maximum Patterns
(4) 3
Quick Set Menu Not supported
Address Range 1-32
Notes:
(1) Requires the AD2083-02 series code converter.
(2) Preset information is stored at the converter, not
the dome.
(3) Requires AD2083-02 with firmware version 0701-
11YB-156A or newer. Preset information is stored
in the dome, not the converter.
(4) Patterns are limited by time and the number of
available dome commands. Total time for each
pattern cannot exceed 6 minutes 50 seconds.
Total dome commands used in all patterns cannot
exceed 99.
AD1650
Supported Protocol RS-422
(1)
Maximum Presets 16
(2)
or 60
(3)
Maximum Patterns
(4) 3
Quick Set Menu Not supported
Address Range 1-128
(5)
Notes:
(1) Requires the AD2083-02 series code converter.
(2) Preset information is stored at the converter, not the
dome.
(3) Requires AD2083-02 with firmware version 0701-11YB-
156A or newer. Preset information is stored in the
dome, not the converter.
(4) Patterns are limited by time and the number of available
dome commands. Total time for each pattern cannot
exceed 6 minutes 50 seconds. Total dome commands
used in all patterns cannot exceed 99.
(5) Requires additional equipment to achieve these
numbers. A dome address within each group of 64 or 99
cameras is reserved as a global broadcast address.
AD168
Supported Protocols SensorNet
(1)
RS-422
(1) or (2)
Maximum Presets 16
(1)(2)
, 64
(1)(3)
, or 60
(4)
Maximum Patterns
(5) 3
Quick Set Menu Not supported
Address Range SensorNet: 1-180
RS-422: 1-99
(1)(6)
or
1-180
(2)(6)
Notes:
(1) Requires the appropriate code control module.
(2) Requires the AD2083-02 series code converter.
(3) Presets information is stored at the converter or control
module, not the dome.
(4) Requires AD2083-02 with firmware version 0701-11YB-
156A or newer. Preset information is stored in the
dome, not the converter.
(5) Patterns are limited by time and the number of available
dome commands. Total time for each pattern cannot
exceed 6 minutes 50 seconds. Total dome commands
used in all patterns cannot exceed 99.
(6) Requires additional equipment to achieve these
numbers. A dome address within each group of 64 or 99
cameras is reserved as a global broadcast address.
A–4 SpeedDome Ultra VII Operator's Manual