intimus 3000 C - Manual (Page 4)

SCOPE OF APPLICATION:
The intimus 3000S / 3000C data shredder is
designed for shredding general printed material
and data media such as CDs, DVDs and credit
cards.
This machine should only be used for
shredding paper and credit cards and
for shredding CDs and DVDs!
Any attempt to shred other types of data
medium may result in damage to the
machine (e.g. destruction of the cutting
mechanism etc.).
INSTALLATION:
- Unpack and set machine upright.
- Plug in the machine (for instructions for the
necessary precautions see „TECHNICAL
DATA“).
The socket outlet shall be installed
near the equipment and shall be easily
accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by “one person only”.
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of
this machine (dimensions, feed openings,
emergency shutdown devices etc.) does not
provide for any guarantee regarding hazard-
free operation by children.
<< Repairs may only be performed by trained
personnel!
<< Danger of injury! Keep all
loose articles of clothing, ties,
jewelery, long hair or other loose
objects away from opening!
<< Danger of injury! Never insert fingers into
opening!
<< Danger of injury! Do not spray and flam-
mable liquids or gases into the inlet open-
ing!
<< In case of danger switch the machine off
with the mains switch, or with the emer-
gency switch, or unplug the machine!
<< Always unplug the machine from the
mains power supply before opening the
machine!
IMPORTANT SAFETY NOTES
CONTROLS:
1 = Pushbutton switch „ready“ (fig. 1)
Depress this switch to start the machine or
to stop the machine.
2 = Rocker switch (fig. 1)
(forward / reverse)
This switch is for the following functions:
- “ ” position
The cutting system operates.
- “ ” position
The cutting system runs in reverse.
3 = Light barrier (forward running) (fig. 2)
The shredding operation starts as soon
as material is fed into one of the two feed
slots.
4 = Pilot lamp „ready“ (fig. 1)
Lights when the pushbutton switch (1) is
operated.
5 = Pilot lamp “material jam“ (fig. 1)
Lights if too much material is fed into the
cutting mechanism. The cutting mechanism
halts, then runs one step in reverse and stops.
The motor switches off.
6 = Pilot lamp “motor overload” (fig. 1)
Lights up if the motor is overloaded. The
machine cannot be started again until the
motor has cooled down.
7 = Pilot lamp (fig. 1)
„receptacle missing“
Lights up when the receptacle is not placed
properly under the machine. The machine is
switched off automatically when the recep-
tacle is removed and cannot be startet if the
receptacle is not placed properly under the
machine.
8 = Pilot lamp
„receptacle full“ / „reverse“ (fig. 1)
a) Model 3000C
Lights when the receptacle is full and
needs to be emptied. At the same time
the machine switches off automatically.
b) Model 3000S
Lights up when the cutting system is swit-
ched to reverse running.
The shredder may not be used as a step
ladder or as a seat. Danger of falling
due to breakage!
MATERIAL FEED:
- Switch on the machine at the pushbutton switch
(1) (fig. 1). The pilot lamp (4) (fig. 1) lights up.
Feeding paper
- Feed the paper into the cutting system through
the paper feed slot (9) (fig. 2).
Note: when shredding transparencies, the
machine should be switched manually to the
forward running position (rocker switch (1)
(fig. 1) to position “ ”.
Feeding data media
- Feed the data media (CDs, DVDs or credit cards)
into the cutting system one by one through the
separate CD/DVD feed slot (10) (fig. 2).
- The machine automatically switches to forward
running and pulls the material in. The machine
switches off again automatically when shredding
is completed.
Never feed the shredder with a quantity
of material exceeding the maximum
indicated. Refer to the TECHNICAL
DATA section!
Should the machine become overloaded,
follow the instructions under “MATERIAL
JAM IN MACHINE” under “MALFUNC-
TIONS”.
RECEPTACLE FULL INDICATOR (Fig. 3)
When the shredded material becomes visible in
the “receptacle full” window (11) (fig. 3) it is time
to empty the receptacle.
Model 3000C
Additional indication functions:
Before the maximum bin level is reached at which
the machine switches off, a beep will sound up
to three times to indicate that it is time to empty
the receptacle.
When the receptacle is full, the machine switches
off. The pilot lamp (8) (fig. 1) lights up.
4
5
6
1
7
8
2
9
10
3
93404 1 08/13
8
3000S
3000C
3000S 3000C
OPERATION
INITIATION
OPERATION
GB Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
fig. 1 fig. 2
4