intimus POWER 16.50 S - Manual (Page 9)

INSTALLATION REQUIREMENTS:
Be certain that three phase current is available at
the point of installation (see TECHNICAL DATA
for information concerning required pre-fusing of
the electrical outlet).
Note: Since this machine can weigh up to 726
kg, it is essential to check the permissible load
per square meter of the floor.
The machine may only be used for its
intended purpose!
The machine’s mains connection must
be freely accessible!
The machine should only be operated
in closed rooms within a temperature
range of 10 to 40° C!
NUMBERED PARTS:
15 = Feed table (fig. 1)
16 = Protective angle, left side (fig. 1)
17 = Protective angle, right side (fig. 1)
18 = Switch flap „Shredder bin full“ (fig. 3)
19 = Levelling screw (fig. 2)
20 = Base frame, left side (fig. 1)
21 = Base frame, right side (fig. 1)
22 = Dividing panel (fig.1)
23 = Shredder bin (fig. 4)
24 = Shredder bin stirrup (fig. 4)
25 = Shredder bin front panel (fig. 4)
INSTALLING THE
BASE FRAMES (Figs. 1 and 2):
1. Remove the dividing panel (22) from between
the two frames (20+21), using the special
purpose spanners provided.
2. Remove both frames (20+21) from the housing
case.
3. Lift the complete unit and rotate the two frames
by 180° so that the open ends of the frame are
facing downwards. Re-attach the frames to the
housing using four screws (M 10x20) and lock
washers.
4. Place the dividing panel (22) beneath the feed
table between the two frames. Attach the plate
to the frames using two screws (M 10x20) and
lock washers.
5. Lower the complete unit and use the plastic
stoppers supplied to seal off the remaining
open holes on the base frame.
Ensure all parts of the base frame
are firmly screwed together before
lowering the shredder!
6. Adjust the levelling screws (19) to compensate
for any unevenness in the floor (fig. 2).
INSTALLING THE FEED TABLE (15) (Fig. 1):
1. Remove the hexagonal nuts and the lock
washers from the 4 projecting screws on the
front panel of the housing.
2. Place the feed table on the conveyor belt so
that the ends of the screws go through the holes
on the feed table. Push the table up against
the housing and attach it to the front panel
using the nuts and washers you have already
removed.
3. To ensure that the feed table is secure, unscrew
the two hexagonal screws under the feed table
as far as possible, and secure each with a
hexagonal nut.
4. Guide the power cable for the emergency-stop
rail (14) through the sleeve on the front side
of the housing, through the cable gland on the
bottom of the switch box, and on into the switch
box. Then connect the blue wire to terminal 20
and the brown wire to terminal 19.
The emergency-stop rail detailed
under point 4 must be installed by
a qualified electrician!
INSTALLING THE
PROTECTIVE ANGLES (Fig. 1):
Secure the two protective angles (16+17) to the
right and left of the feed table (15) using the 6 flat
headed screws.
INSTALLING THE SWITCH FLAP (Fig. 3):
Screw the switch flap (18) to the hinge located
at the outlet (behind the cutter), using the two
available screws, as illustrated.
INSTALLING THE
SHREDDER BIN (23) (Fig. 4):
Only the original shredder bin which
was delivered with the machine may
be used!
The use of other shredder bins is not
permitted because this might allow the
operator to reach into the underside of
the machine and represents a safety
hazard.
Note: The connecting bolts and locking elements
used to connect the back panel, the two side pa-
nels, and the base frame are included in delivery.
Insert the bolt through the panel you wish to connect
and match it to the locking element on the other
part. Turning the locking element clockwise (in the
direction of the arrow) secures the bolt.
To assemble the shredder bin proceed as fol-
lows:
1. Connect the back panel to the base frame.
2. Connect the side panels (lighter shaded side
facing inwards) to the base frame and back
panel.
3. Connect the front panel (25) to the base frame
using the hinge bolts supplied (insert the hinge
bolts into the hinges from the outside).
4. Insert the stirrup hinge bolts through the side
panels, as illustrated. Then, place the ends of
the stirrup (24) through the holes in the hinge
bolts, and finally, secure the stirrup using the
two locking screws.
5. Attach the buffers to the front panel, as illust-
rated.
6. Insert the base plate, bring up the front panel
and secure in place with the stirrup.
7. Now you can place a plastic bag in the bin and
fold the end of the bag over the bin rim.
15.90 S/16.50 S
84236 9 01/13
INSTALLATION
GB
9
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung