intimus PacMaster S - Manual (Page 4)

APPLICATIONS:
The
PacMaster VS is used for the manufacture
of packaging pads made from corrugated board
or other carton materials.
Only corrugated cartons and similar
materials may be fed into the machine
for processing into packaging pads!
The use of other materials may result in
bodily injury (e.g. due to splintering of hard
materials etc.), as well as damage to the
machine (e.g. destruction of the cutting
system etc.).
INSTALLATION REQUIREMENTS:
- Unpack machine and install it in accordance with
the label on the packing film.
- Plug in the machine.
The machine may only be used for its
intended purpose.
The mains connection at the machine
must be freely accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 40°C!
The machine is approved for operation
at an altitude of up to 1000 m above
sea level and relative humidity of up
to 50% with an outside temperature
of 40° C.
MOTOR FAILURE:
The machine is equipped with a thermally pro-
tected motor. Should this motor be overloaded, it
will switch off automatically. In such case the pilot
lamp „ready“ (5) (fig. 2) flashes.
After a cooling down period of approx. 5-10 minutes
(depending on the room temperature) you can
restart the machine and continue shredding.
Note: When the motor is overloaded, only the
forward run is cut off. To take the excess material
out of the inlet opening, the cutting system may
at any time be switched on „reverse“. FAULT CHECKLIST:
If the machine is not functioning properly, you
should check the following:
- Is the unit
plugged into the mains power
supply?
- Is the mains switch (1) turned on?
- Is the motor overloaded?
Please refer to „Motor Failure“.
If you still cannot isolate the fault after carrying
out all these checks, please notify our customer
service department.
Always unplug the machine from the
mains power supply and turn off the
mains switch before opening the ma-
chine to carry out any repairs.
GEAR BOX MAINTAINANCE:
The gear wheels, as well as the chain wheels and
drive chains must be greased
monthly.
The machine must be turned off at the
mains switch (1) (fig. 1) and unplugged
before the machine is opened.
Proceed as follows:
1. Remove the left side cover and the right side
cover from the housing.
2. Grease the above mentioned parts with a brush
or a grease gun, and a standard, commercially
available grease.
3. Re-install the side covers and connect the
machine to the mains. The machine can be
put back into operation.
No structurel modifications may be
carried out!
In case of non-observance, the opera-
tion permission expires.
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by “one person only”.
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of this ma-
chine (dimensions, feed openings, emergency
shutdown devices etc.) does not provide for
any guarantee regarding hazard-free operation
by children.
<< Danger of injury! Keep all
loose articles of clothing, ties,
jewelery, long hair or other loose
objects away from opening!
<< Danger of injury! Never insert fingers into
opening!
<< In case of danger switch the machine off
with the mains switch, or with the emer-
gency switch, or unplug the machine!
<< Always unplug the machine from the
mains power supply before opening the
machine!
Repairs may only be performed by trained
personnel!
IMPORTANT SAFETY NOTES
PacMaster VS
88386 5 1
1/12
INITIAL START UP
MALFUNCTIONS
TECHNICAL DATA
Cutting width: 4x110 mm
Cutting capacity: 3 layers
corrugated board
quality 3.1
(max. thickness of
cor. boards 18 mm)
Inlet guide
cutting system:
15 mm
Working width
cutting system:
425 mm
Cutting speed: 0.09-0.29 m/sec.
Power consumption: 2.3-2.9 kW
Intermittent service: 30 min – 15 min
Supply voltage: 230V/50Hz
240V/50Hz
220V/60Hz
Pre-fusing:
230V/220V:
16 A
240V: 13 A
Width: 685 mm
Depht: 470 mm
Height: 950 mm
Noise level: approx. 68.5 dB(A)
Weight: approx. 185 kg
MAINTENANCE
GB
DISPOSING OF THE MACHINE:
Dispose of the machine in an
environmentally sound fashion at the end
of its useful service life. Do not dispose of
any of the parts included in the machine
or its packaging with household trash.
DISPOSING
ACCESSORIES
CONNECTION OF VACUUM CLEANER:
In order to reduce the development
of dust during the production of filler
pads, the PacMaster S is fitted with a
connector sleeve, diam. 50 mm, sui-
table for the connection of all common
industrial vacuum cleaners.
Note: For orders of special accessories and spare
parts, please contact your dealer.
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
4