Assembly/installation, Figure 6, Figure 9 – Level Mount DCDSK30SJ User Manual
Page 6: Figure 8, Figure 10, Figure 7
6
www.levelmount.com
1-888-229-1459
EU: +0044 844 567 2657
UK: 0844 567 2657
©2011 Level Mount - Patents Pending
Assembly/Installation
Step 3 – Attaching Flat Panel Monitor Bracket to Back of
Flat Panel Monitor
There are bolts of varying lengths included in this package, located in (Bags 1 and
2). Please use the bolt with the appropriate length for your Flat Panel Monitor.
• Bolt M4 (Bag 1) or Bolt M5 (Bag 2)
• Washer M4 (Bag 1) or Washer M5 (Bag 2)
• An additional Washer may be needed to prevent the bolt head from recessing
into the back of the Flat Panel Monitor
• Adapter
Arm
• Spacer (Bag 1) Only needed if the Flat Panel Monitor has a recessed back.
To attach the Flat Panel Monitor Bracket to the back of the Flat Panel Monitor,
place 4 Bolts through the holes of the Flat Panel Monitor Bracket and carefully
thread them into the holes in the back of the Flat Panel Monitor. If there is any
resistance remove the bolt immediately and select the correctly sized bolt that
enables a secure and snug fit.
Tighten the bolts snugly to the back of the Flat Panel Monitor as shown in Figure 7.
Caution:
Only tighten bolts until they are secure, do not over-tighten.
Flat Back Monitor
M4/M5 Washer
M4/M5 bolt
Monitor Bracket
Figure 6
Phillips
Screwdriver
Only use Spacer if Monitor has a recessed back
Spacer
Step 4 – Securing the Desktop Arm and Arm Plate to
the Desk
Place the L-Bracket portion of the Desktop Arm on the desk as shown in
Figure 8. Turn the Securing Knobs clockwise until they are snug against the
desktop as shown in Figure 9.
In most cases the L-bracket bolts will be the correct depth. However, in some
cases the L-Bracket will need to be adjusted due to the depth of the desk top.
To adjust the bolts in the L-Bracket simply unscrew the L-Bracket bolts and fit
to the desk. Then tighten the bolts securely.
Caution:
The L-bracket only fits a ledge that is between .5 and 2.5
inches thick, and at least 2 inches deep. If the desktop ledge is made
out of a material other than solid wood, you will need to make sure
that the ledge can support the weight of the mount and Monitor/
Display placed on the desktop.
Attach the Arm Plate to the holes in the Desktop Arm, at the desired height
depending on the size of the Flat Panel Monitor, as shown in Figure 10 using
the hardware from (Bag 3) as follows:
• Bolt M6 (Bag 3)
• Arm
Plate
• Desktop
Arm
• Washer 16mm x 6.3mm x 1.2mm (Bag 3)
• Hex Nut M6 (Bag 3)
Securing Knobs
Securing Knobs
Figure 9
Desk Top
Desk Top
Arm
Desk Top
Desk Top
Arm
Securing Knobs
Securing Knobs
L-Bracket
Bolts
Figure 8
L-
Thin Desk
Top
Desk Top
Arm
Thick Desk
Top
Desk Top
Arm
L-Bracket
Bolts
Washer
16mmx6.3mmx1.2mm
M6 Bolt
Arm Plate
Desk Top Arm
M6 Hex
Nut
Figure 10
Phillips
Screwdriver
M6 Bolt
Phillips
Screwdriver
p
p
Desk Top
Monitor Bracket
Figure 7
Flat Back Monitor
M4/M5
Bolt