Nitek ET1500UWS User Manual
Nitek, Product specifica t ion, Models
MODELS:
EL1500UW, ET1500UW,
EL1500UWS, ET1500UWS
Outdoor Rated Ethernet
& PoE Extender
PRODUCT SPECIFICA
T
ION
08132013
NITEK
®
De Schans 19-21 2a
8231 KA Lelystad
Tel: +31(0)320-230005
E-mail: [email protected]
WWW.NITEK.NL
USA
5410 Newport Drive, # 24
Rolling Meadows, IL 60008
Phone: (847) 259-8900
Fax: (847) 259-1300
E-mail: [email protected]
WWW.NITEK.NET
EUROPE
Description
Four models EL1500UW, ET1500UW, EL1500UWS, and
ET1500UWS are part of the EtherStretch solution allowing for
outdoor installation. The models listed in the Nitek catalog
with a “W” are intended for outdoor applications. The “ET”
models are shipped with just the NEMA Enclosure and an
ET1500U EtherStretch transmitter. The “EL” models are
shipped with both the ET1500U transmitter and the ER1500U
receiver EtherStretch units. The “S” incorporates the
IPPWR1 surge protector.
The WP1325 is a polycarbonate and high-impact ABS
molded enclosures meet NEMA 4X specifications and are
ideal for use when installing Nitek products outdoors. The
units is equipped with a neoprene gasket to prevent Ingress
of moisture and dust. The cable entries into the box are made
through the UL94V-2 rated nylon hex nut cable seal which is
required to maintain NEMA 4X ratings when cables enter or
exit a NEMA 4 or 4X type enclosure. The WP1325 is often
ordered as a “W” option with other Nitek products.
The ET1500UW contains a transmitter constructed of
industrial grade RoHS compliant plated corrosion resistant
aluminum finish. It works with any of the EtherStretch multi-
port systems, as-well-as the single port receiver ER1500U.
Our EtherStretch solution allows for the utilization of existing
cable infrastructure (coax or UTP) to transmit data from IP
cameras and other network devices along with power (PoE)
to operate these networked devices well beyond standard
network limitations. The system can extend Ethernet to over
600m or 2000ft of category cable making the ET/EL1500UW
ideal for retrofitting existing installations.
The ET1500UW requires very little installation time and no
set up or configuration. The ET1500UW is transparent to the
network thus requiring no IP and MAC addressing. Simply
connect your network devices to the networking ports of the
transmitter and receiver along with existing cabling, ordinary
four pair UTP cable, and the system begins communicating.
LED indicators show the status of network communication
and PoE power. The ET1500UW requires no network settings
to be changed or adjusted.
The IPPWR1 is a single channel, in-line, 10/100/1000
Ethernet surge protector for IP cameras. In addition it
provides independent protection for 12 or 24 volt power,
which can be used with heaters, blowers or PTZ. The
IPPWR1 has standard RJ45 jacks for easy connection and
is ideal for small or restricted spaces. The IPPWR1
provides a heavy duty, single point ground connection and
is easy to install in minutes.
RoHS
COMPLIANT
2002/95/EC
IEC/UL 60950-1
Bottom (Side View)
Top (Side View)
Ma
d
e
in
U
S
A
NI
TEK
E
T
1
500
U
T
ransm
itter
M
a
d
e
in
U
S
A
NI
TEK
E
T
15
00U
T
ran
sm
it
ter
NITEK Model: ET1500UWS
NITEK Model: ET1500UW
2.17
5.74
4.56
8.25
9.92
8.74
2.5
.9
1.8
NITEK Model: IPPWR1
1.1
Made in USA
NITEK
ET1500U
Transmitter
NITEK Model: ET1500U
1.6
4.6
EL1500UWS