PASCO OS-8526A X-Y ADJUSTABLE DIODE LASER - Manual

RE D D IOD E L AS ER
003 -10 496
AVO ID E XPO SUR E
LAS ER LIG HT IS E MIT TED
FRO M T HIS AP ERT URE
®
101 01 F ooth ill B lvd.
Ros evil le, C A. 9 574 7 U SA D DIODE LASER 3 10496
®
10101 Foothill Blvd.
Roseville
, CA.
95747 USA
OS -85 26A
X-Y
ADJUST
ABLE
DIODE LASER 101 01 F ooth ill B lvd.
Ros eville , CA 957 47 U SA
®
Man ufac ture d by :
Complies with FDA performance st
andards for
laser product
s except for
deviations
pursuant
to Laser
Notice No. 50, dated June 24, 2007
LASER LIGHT DO NOT ST
ARE
INT
O BEAM
CLASS 2 LASER PRODUCT 650nm, <1mW CW (Red) CLASSIFIED 60825-1 2007
Instruction Sheet
for the PASCO
Model OS-8526A
X-Y ADJUSTABLE DIODE LASER
012-12246A
Introduction
The X-Y Adjustable Diode Laser allows users to eas-
ily incorporate laser light into a wide variety of labora-
tory experiments. Designed to be mounted on a rod
stand, the X-Y Adjustable Diode Laser can rotate
360° allowing the user to set up the unit in virtually
any position.
Equipment
– X-Y Adjustable Diode Laser.
– 9VDC adapter
Additional equipment recommended:
– PASCO ME-8735 Large Rod Stand
– PASCO ME-8738 (90 cm) or ME-8741 (120cm)
support rod
Replacement parts:
Description PASCO part no.
thumbscrew assembly 617-016
Specifications:
Wavelength 650 nm
Laser Power for classification <1 mW
Divergence <2 mrd
Beam Diameter at aperture: 3 mm
➤
CAUTION - use of controls or adjustments
or performance of procedures other than those
specified herein may result in hazardous radia-
tion exposure.
• LASER LIGHT - DO NOT STARE INTO BEAM.
• CLASS 2 LASER PRODUCT
• This Laser Product is designated as Class 2
during all procedures of operation.
• Do not point the laser or allow the laser to be
directed or reflected toward people or animals.
Phone (916) 786-3800 • FAX (916) 786-8905 • web: www.pasco.com
10101 Foothills Blvd. • Roseville, CA 95678-9011 USA ®
better
teach science
ways to
ME-8735 Large Rod Stand
(not included)
Figure 1: Setting Up the OS-8526A
X-Y Adjustable Diode Laser
support rod
thumbscrew
“fixed” rod
clamp
OS-8526A X-Y
Adjustable Diode
Laser
RE D D IOD
E L AS ER
003 -10 496
AVO ID E XPO SUR E
LAS ER LIG HT I S EM ITTE D
FRO M T HIS AP ERT URE
®
OS-8526A
X-Y
ADJUST
ABLE
DIODE LASER 10101
Foothill B
lvd.
Rose ville , CA 9 574 7 US A
®
Man ufactured b
y:
Complies with FDA
performance st
andards for
laser product
s except for
deviations
pursuant
to Laser
Notice No. 50, dated June 24, 2007
LASER LIGHT DO NOT ST
ARE
INT
O BEAM
CLASS 2 LASER PRODUCT 650nm, <1mW CW (Red) CLASSIFIED 60825-1 2007
Assembly
➀
Attach the “fixed” rod clamp, with the locking
knob permanently affixed, to a base rod up to 1/2”
(12.5 mm) in diameter. See Figure 1.
Complies with FDA
performance standards for
laser products except for
deviations pursuant to Laser
Notice No. 50, dated June 24, 2007
LASER LIGHT
DO NOT STARE
INTO BEAM
CLASS 2 LASER PRODUCT
650nm, <1mW CW (Red)
CLASSIFIED 60825-1 2007
Warning Label
Mfg. I.D. Label