HTP EFT-399 - Manual (Page 68)

68
LP-387 REV. 6.10.14
Function 24 Cascade Rotation
CASCADE ROTATION
48 HOURS 24 Sets the amount of hours before the first boiler in the cascade firing rotation will be changed. NOTE: If this parameter is
set to 0, the firing order of the boilers will not rotate. Default: 48 hours (Range: 0
– 240 hours).
Function 25 Cascade DHW Mode
NOT USED
NOT USED 25 Not used on this product.
Function 26 System Freeze Protect
SYS FREEZE PROT
PROTECT OFF 26
NOTE: This parameter is only present if the boiler is a cascade master. Allows the user to set the freeze protection
when a system pump is used. Factory Default: OFF. Selection of temperature activates freeze protection. (Range:
OFF, -40
o F – 104 o F).
Function 27 Error System Sensor
ERROR SYSTEM SENS
ON 27 Allows the user to set the control to display an error message if the system sensor is open or shorted. NOTE: This
error does not stop the boiler (or boilers) from running. Factory Default: ON (Range: ON / OFF).
Function 28 Freeze Protection
FREEZE PROTECTION
ON 28 Allows the user to set freeze protection on the boiler. Factory Default: ON (Range: ON / OFF).
Function 29 DHW Modulation Mode
DHW MODULATE MODE
NORMAL MOD 29
This parameter controls how the boiler modulates for a DHW demand. In NORMAL MOD mode, the boiler will
modulate down from high fire when there is a DHW demand. In LOW MOD mode, the boiler will modulate up from low
fire when there is a DHW demand. This mode is useful to minimize short cycling when a large boiler and small indirect
tank are used together. Factory Default: NORMAL MOD (Range: NORMAL MOD / LOW MOD).
Function 30 Extra Boiler Mode
EXTRA BOILER MODE
OFF 30
Allows for a non HTP boiler to be controlled when the cascade output has risen above the percent of the cascade firing
rate set in this parameter. Factory Default: Off (Range: 50% - 100%).
Function 31 System Sensor Mode
SYSTEM SENSOR MODE
OFF 31 Suppresses the ‘NO FOLLOWER’ message on the display if the boiler is used as a cascade master boiler with no
follower boilers connected. Factory Default: OFF (Range: ON / OFF).
Function 32 Service Schedule
SERVICE SCHEDULE
OFF 32
Allows the user to select a service date or time based on the boiler run hours to program the boiler maintenance
schedule. Factory Default: OFF (Range: Date or Run Hours). NOTE: Without setting this function, Functions
33/34/35/36 will not display.
Table 20 – System Setting Menu Screens
NOTE: For the following functions, you must have your maintenance function turned on.
To change, press ENTER. The left most digit will begin to blink. Use the up
▲ or down ▼ arrows to change the digit. Use the  
arrow keys to switch between digits. When you’ve made your selection, press ENTER again.
SCREEN DESCRIPTION
Function 33 Year
SERVICE SCHEDULE
YEAR 00/00/2000 33 Allows the user to set the year of the next service reminder.
Hours
SERVICE SCHEDULE
10000’s
00 0000h 33
Allows the user to set the left two digits of the amount of run hours before next service reminder.
Function 34 Month
SERVICE SCHEDULE
MONTH 00/00/2000 34 If the date function was selected, this function allows the user to program the month. If you selected the run hour
function, you will need to program 10,000 hours, if required.
Hours
SERVICE SCHEDULE
10000’s 00
00 00 34
Allows the user to set the two middle digits of the amount of run hours for the next service reminder.
Function 35 Day
SERVICE SCHEDULE
DAY 00/00/2000 35 Allows the user to set the day of next service reminder.
Hours
SERVICE SCHEDULE
10000’s 0000
00 35
Allows the user to set the 2 right digits of the amount of run hours for the next service reminder.
Function 36 Telephone
TELEPHONE #
000 000 0000 36 Allows the user to input a telephone number that will be displayed when maintenance is required.
Table 21 – Maintenance Reminder Function Screens
G. RESETTING THE MAINTENANCE SCHEDULE
When the system control flashes MAINTENANCE REQUIRED, it is advisable that you call for service. After the service is performed,
reset the schedule for the next required service by using the following steps.