Foredom Safety Instructions for Using - Manual (Page 8)

A jewelers bench with a solid, flat work
surface is ideal. The PowerGraver motor
can be suspended from a Foredom motor
hanger (See Illustration No. 12) attached
to the side (right for right handed/left for
left handed) of the bench with clamp
(MAMH-3 or MAMH-5), or it can be bolted
on (MAMH-4 or MAMH-6). Each can be
raised or lowered to the most comfortable
height for you. Their special motor bracket
hook reduces motor twisting when started
at medium to high speed. Each one also
has a handpiece rest to hold the 9D hand-
piece out of your way when not in use. Some jewelers benches are made with
lower (30
″ high) work surfaces for
engraving work done with engraving
blocks since they raise the workpiece
above the work surface about 8
″– 12″.
You can also mount the block on a shelf or
extension table below the bench surface.
Chairs with adjustable height are also a
good idea. A flexible arm light (with or
without a magnifier) is almost essential for
doing stone setting and engraving work.
Illustration No. 12
MAMH-4
Motor Hanger
Handpiece
Rest
C.FCGX Foot Switch
Optional On/Off foot switch turns motor on at
the speed set on the EMGX dial speed control.
six foot long power cord.
A-R15G Pavé Point
Optional Diamond Point mounted on
3/32
″ shank.
Optional PowerGraver ®
Equipment and Accessories
FOREDOM ®
The Foredom Electric Company
16 Stony Hill Road, Bethel, CT 06801 USA
• (203)792-8622 • Fax: 203-796-7861 •
www.foredom.com
C.EMGX Dial Speed Control
Solid state dial control in plastic housing. Motor
speed can be varied from 500 to 2,800 strokes
per minute and set at the optimum speed
or the job.
M.PGX Motor
Permanently lubricated ball bearing motor for
quiet, trouble free performance. This smooth
running, high torque motor is designed
specifically for use with the 9D handpiece for
power assisted engraving and stone setting.
The M.PGX Motor can be used with other
Foredom handpieces for low speed, high torque
operations such as polishing. Motor also comes
equipped with a special, extra flexible neoprene
sheath and a six foot long power cord. The
M.PGX Motor has a Full Two Year Warranty.
K.2293 – for 115V AC
K.2293-2 – for 230V AC
PowerGraver ® Kit K.2293 Contains:
Form 920b n 6/08 Printed in USA
H.9D Handpiece
Chuck type handpiece comes with 4 inter-
changeable collets (1⁄16
″, 3/ 32″, 1 / 8″, and
3mm) for holding different sizes and shapes of
popular gravers, as well as beading and setting
tools. Adjusting ring changes impact force. The
palm rest provides the comfort and "feel" of a
hand engraving tool. This handpiece has a
special quick disconnect which fits only the
PGX Motor sheath.
K.2293 Accessories –
Collets
HP602 – 1/16 ″
HP603 – 3/32 ″
(2.35mm)
HP604 – 1/8 ″
HP605 – 3mm
Set of 4 Gravers
Square, Onglette, Round, Oval
Points with 3/32 ″ (2.35mm) shanks
A-10215 Carbide Stylus
A-10177P Anvil Point
Maintenance Supplies
MS10005 Handpiece Oil in Dispenser
MS10006 Flexible Shaft Grease in Tube
A DVD with 32 minutes of instruction for
using the PowerGraver
A Good Workbench Layout will Improve
Comfort and Efficiency –