Rapid-Air MINI-SERVO FEED: MS2, MS4 & MS8. 115vac, 1ph, 60hz - Manual (Page 6)


The intent of this section is to familiar-
ize the operator with the flow of the
program and what to expect with each
key press. Each program screen of
the servo will be displayed and also
comments to clarify possible questions.
There are four sections that will be
explained and they are as follows:
SECTION.1.—
. JOB.NUMBER
SECTION.2.—.
. MANUAL.MODE.
SECTION.3.—.
. AUTOMATIC.MODE
SECTION.4.—.
. REVIEW.JOB.PARAMETERS.
When the servo is first started, and
has performed its startup procedure,
the first screen displayed should look
like this:
. MAIN.SELECTION.MENU.
. . F1=JOB.NUM.F2=MANUAL.
. . F3=AUTOMATIC.(CYCLE)
. . F4=REVIEW.PARAMETERS.
*SELECT.F1=JOB.NUM.
The first step in programming a job is
to select a two digit job number which
will be used to store the parameters
that the operator inputs or to recall
an existing job number that was
previously loaded. When the operator
presses F1 on the keypad, the screen
will change to:
. JOB.SELECTION.MENU.
. . ENTER.JOB.NUMBER=_____
. . PRESS.F4.KEY.AFTER.
. . CORRECT.#.IS.ENTERED.
The next screen lets you program
parameters or exit with the existing
parameters.
oPerATor inPUT seCTion
Operator.Input.Section
. INCH.MODE:
. F1=JOG.FORWARD
. F2=JOG.REVERSE
. F4=RETURN
.......
When the F1 key is pressed, the feed
will advance the material at a slow
rate of speed. When the F2 key is
pressed, the feed will reverse the
material and run at a slow rate of
speed. Press F4 to return to the
main screen.
With the main menu displayed
and pressing the “F3 AUTOMATIC
(CYCLE)”, the following screen
appears:
. . AUTOMATIC..JOB=01
. . FEED.LENGTH=._____
. . PRESS.SPEED=._____
. . F4=RETURN
In the automatic mode, the feed
length and operator entered press
speed will be displayed. Whenever
the press mounted feed switch is
activated, the servo will feed the
feed length displayed on the screen.
Because there is not an interface in
the control for the pilot release it will
be up to the customer to wire the pilot
release switch to the solenoid that
operates the raising of the rolls.
Press F4 button to return to the main
menu and deactivate the automatic
control.
Press F4 again and the final mode is
review parameters, the parameters
for the job number will then be
displayed.
JOB.NUMBER=._____
. . F1=PROG..PARAMETERS.
. . F4=DON’T.ALTER.VALUES.
Pressing the “F1 PROG. PARAMETERS”
key initiates the following screen.
Key in the required parameters.
. FEED.LENGTH=._____
. PRESS.SPEED=._____
. FEED.ANGLE=._____
* Once the parameters have been
entered, the program will complete
the math routine which selects the
proper accel./decell. and motor speed
for the parameters listed and then the
main menu is displayed again.
*.SELECT.F2....MANUAL
If the operator elects to move the
material from the feed to the die
electrically, the manual mode has to
be selected. Pressing the F2 key will
bring up the manual mode screen.
MANUAL.LENGTH=._____
. . F1=SINGLE._.FEED
. . F2=GO.TO.INCH.MODE
. . F4=RETURN
Each time the F1 key is pressed,
the servo will move the material
the feed length entered for the job
number. The material will move at
the speed required to keep up
with the programmed press strokes
per minute.
If the operator would like the material
to move a slower rate then the inch
mode should be selected. Press F2
now to display the inch mode screen.