STI 7511F-HTR - Manual

Safety Technology International, Inc.
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: 248-673-9898 • Fax: 248-673-1246
Toll Free: 800-888-4784 • E-mail: [email protected]
Web: www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999
Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only)
E-mail: [email protected] • Web: www.sti-europe.com
INSTALLATION OF HEATED POLYCARBONATE ENCLOSURE STI-7510A&F-HTR, STI-7511A&F-HTR
All specifications and information shown were current as of publication, and are subject to change without notice.
7510A-HTR IS JULY 2007
IF CONDUIT HUB
IS NEEDED ORDER
SUB-6297B20
HUB KIT, GASKET
AND FASTENERS
NOTE:
SUB KIT IS
3/4 in. RIGID
DIE CAST
SUB-6297B20
3/4” NPT CONDUIT
HUB KIT (NOT
INCLUDED)
MOUNTING TABS & FASTENERS
19013 #10 x 1 1/2” PAN HEAD SCREW
07503 THUMB LOCK (SHOWN)
STI-7511F-HTR
18050 KEYLOCK STI-7510F-HTR
19033 PLASTIC ANCHOR
ILLUSTRATION 2
19013 #10 x 1-1/2 PAN
HEAD SCREW (4) PROVIDED
06297T MOUNTING
TAB (4) PROVIDED
19033 #10-12 PLASTIC
ANCHOR (4) PROVIDED
06297A-M BACK BOX
629721A FRAME GASKET
19002 #8-32 x 3/8”
PAN HEAD MACH SCREW
(4) PROVIDED
SUB-7500-HTR ASSEMBLY
19051 #8-32 x 3/8”
FLAT HEAD SCREW
(4) PROVIDED
19083 M-F #8-32 x 3/8”
STANDOFF (4) PROVIDED
*ADDITIONAL STANDOFFS MAY BE REQUIRED
WHEN USING A WATERTIGHT CONDUIT HUB.
19083 M-F #8-32 x 3/8”
19093 M-F #8-32 x 1-1/2”
19056 M-F #8-32 x 3”
(NOT INCLUDED)
18021 3/4” NPT
WATERTIGHT CONDUIT
HUB (NOT INCLUDED)
07503 THUMB LOCK - STI-7511A-HTR
18050 KEY LOCK - STI-7510A-HTR
629723 COVER GASKET
DRILL (4) 1/4” DIAMETER
HOLES 1 1/4” DEEP
BACK BOX
ILLUSTRATION 1
HEAT ON
POWER
REMOVE
H
INSTALLATION INSTRUCTIONS
1. Remove heater plate assembly (Illustration 1) from back box by
removing 4 flat head screws and set aside.
2. Mount back box and cover assembly in desired position. With
hinges horizontal or vertical, insert the (4) mounting tabs into
the back box slots (see Illustration 2). Mark and drill (4) 1/4”
diameter holes 1 1/4” deep. Insert plastic anchors and screw
back box to wall with (4) #10 x 1 1/2” screws.
3. Route wires for heater and appliance into back box through
conduit or small hole properly sealed.
HEAT
ON
POWER
5.59 in.
(142mm)
7.53 in.(191mm)
4.04
1.88
Electronic warranty form at www.sti-usa.com/wc14