Document Outline

• Copyright © 2013 Brocade Communications Systems, Inc. All Rights Reserved.
• Brocade Communications Systems, Incorporated
• Document History
• About This Document
  • In this chapter
  • Audience
  • Supported hardware and software
    • Supported software
  • Document conventions
    • Text formatting
    • Notes, cautions, and danger notices
  • Notice to the reader
  • Related publications
  • Getting technical help or reporting errors
• Configuring IP Multicast Protocols
  • Overview of IP multicasting
    • Multicast terms
  • Changing global IP multicast parameters
    • Concurrent support for multicast routing and snooping
    • Defining the maximum number of DVMRP cache entries
    • Defining the maximum number of DVMRP routes
    • Defining the maximum number of PIM cache entries
    • Defining the maximum number of multicast VRF CAM entries
    • Defining the maximum number of IGMP group addresses
    • Changing IGMP V1 and V2 parameters
  • Mtrace overview
    • Mtrace components
    • Configuring mtrace
  • Support for Multicast Multi-VRF
    • System max parameter changes
    • Show and clear command support
  • Adding an interface to a multicast group
  • Multicast non-stop routing
    • Configuration considerations
    • Configuring multicast non-stop routing
    • Displaying the multicast NSR status
  • Passive Multicast Route Insertion (PMRI)
    • Configuring PMRI
    • Displaying hardware-drop
  • IP multicast boundaries
    • Configuring multicast boundaries
    • Displaying multicast boundaries
    • Performing IPv4 Multicast RPF shortcut using LSP paths
    • Multicast ECMP support
    • Limitations and prerequisites
  • PIM Dense
    • Initiating PIM multicasts on a network
    • Pruning a multicast tree
    • Grafts to a multicast tree
    • PIM DM versions
    • Configuring PIM DM
    • Failover time in a multi-path topology
    • Modifying the TTL threshold
    • Configuring a DR priority
    • Displaying basic PIM Dense configuration information
    • Displaying all multicast cache entries in a pruned state
    • Displaying all multicast cache entries
    • Multicast PIM neighbor filter
  • PIM Sparse
    • PIM Sparse device types
    • RP paths and SPT paths
    • Configuring PIM Sparse
    • ACL based RP assignment
    • Route selection precedence for multicast
    • PIM multinet
  • Multicast Outgoing Interface (OIF) list optimization
    • Displaying PIM Sparse configuration information and statistics
    • Clearing the PIM forwarding cache
    • Displaying PIM traffic statistics
    • Clearing the PIM message counters
    • Displaying PIM counters
  • Configuring Multicast Source Discovery Protocol (MSDP)
  • Configuring MSDP mesh groups
    • Configuring MSDP mesh group
  • MSDP Anycast RP
  • PIM Anycast RP
    • Configuring PIM Anycast RP
  • DVMRP overview
    • Initiating DVMRP multicasts on a network
    • Pruning a multicast tree
    • Grafts to a multicast tree
  • Configuring DVMRP
    • Enabling DVMRP globally and on an interface
    • Modifying DVMRP global parameters
    • Modifying DVMRP interface parameters
    • Displaying DVMRP information
  • Configuring a static multicast route
    • Configuring a static multicast route within a VRF
  • IGMP V3
    • Source-specific multicast
    • Configuring PIM SSM group range
    • Configuring multiple SSM group ranges
    • IGMPv2 SSM mapping
  • IP multicast traffic reduction
    • Configuration requirements
    • Configuring IP multicast traffic reduction
    • PIM SM traffic snooping
    • Multicast traffic reduction per VLAN or VPLS instance
    • IP Multicast CPU Protection
    • Static IGMP membership
    • Displaying IP multicast information
  • Commands
    • multicast-routing load-sharing
    • multicast-routing load-sharing rebalance
    • pim neighbor-filter
    • show ip|ipv6 pim interface
    • rpf shortcut
• Configuring IPv6 Multicast Features
  • IPv6 PIM Sparse
    • PIM Sparse router types
    • RP paths and SPT paths
    • RFC 3513 and RFC 4007 compliance for IPv6 multicast scope-based forwarding
    • Configuring PIM Sparse
    • IPv6 PIM-Sparse mode
    • Configuring IPv6 PIM-SM on a virtual routing interface
    • Enabling IPv6 PIM-SM for a specified VRF
    • Configuring BSRs
    • Route selection precedence for multicast
    • Enabling Source-specific Multicast
    • Configuring a DR priority
    • Passive Multicast Route Insertion
    • Displaying PIM Sparse configuration information and statistics
    • Clearing the IPv6 PIM forwarding cache
    • Clearing the IPv6 PIM message counters
    • Updating PIM Sparse forwarding entries with a new RP configuration
    • Clearing the IPv6 PIM traffic
    • Setting the maximum number of IPv6 multicast routes supported
    • Defining the maximum number of IPv6 PIM cache entries
    • Defining the maximum number of IPv6 multicast VRF CAM entries for all VRFs
  • PIM Anycast RP
    • Configuring PIM Anycast RP
  • Multicast Listener Discovery and source-specific multicast protocols
    • Enabling MLDv2
    • Configuring MLD parameters for default and non-default VRFs
    • Configuring MLD parameters at the interface level
    • Displaying MLD information
    • Clearing IPv6 MLD traffic
    • Clearing the IPv6 MLD group membership table cache
  • IPv6 Multicast Listener Discovery snooping
    • Configuring IPv6 multicast routing or snooping
    • Enabling IPv6 multicast traffic reduction
    • PIM-SM traffic snooping
    • Configuring IPv6 MLD snooping on a per-VLAN basis
    • Displaying IPv6 multicast information