FallTech Sling Anchors - Manual (Page 14)

27
that each D-ring or O-ring is used for only a single
connection.
10. Proceed cautiously with your work. Do not run, jump or over-
reach. Any type of sudden movement may cause you to
lose your footing. Move with care and deliberation at all
times while tied-off and working at heights.
11. Do not allow your connecting device to pass under your arm or
between your legs – severe injury or death may result. Also
avoid sharp edges which may damage your connecting device in
the event of a fall.
12. If the structural member that this Carabiner Sling Anchor is
attached to is sloped or vertical, the Carabiner Sling Anchor must
be positioned next to a stop which will prevent it from sliding or
moving in the event of a fall.
13. If you are tied-off at the foot-level, or in a manner that will allow
more than six feet of free fall, ensure that your connecting device
is rated for extended free falls. Also ensure that the gate of your
carabiner or snap hook which is attached to the Carabiner Sling
Anchor does not make direct contact with the edge of the
structural member or any other obstruction. Such contact could
force a roll-out or accidental disengagement.
Once the above steps have been taken, the user will have access to
their work area while walking and moving at normal speeds. It is
important not to make sudden or dramatic movements! When using this
device, care must be taken to be aware of the work environment and any
hazards, obstructions or obstacles that may exist. Be careful of any and
all fall hazards and also be aware of slipping and tripping hazards as
well.
Fig. 3.6
Correct Installation of Carabiner Sling Anchor
28
3.10: Installation and Use – Cable Anchor Extenders
1. Read, understand and comply with manufacturer’s instructions
for each component of your Personal Fall Arrest System (Full-
Body Harness, Connecting Devices, Anchorage Connectors,
etc.). Be sure to choose components that are compatible with
this Cable Anchor Extender. If you have questions about
product or component compatibility, be sure to contact FallTech
for additional instructions.
2. Calculate possible swing fall hazards, total fall distance, and
required clearance distance. If you have a swing-fall hazard or
do not have the required clearance distance, STOP and
reevaluate your application and system. Your work location
should never exceed an angle of 15 degrees in any direction in
relation to your anchorage location.
3. Inspect this Cable Anchor Extender, and all components of your
Personal Fall Arrest System in accordance with Section 8 of this
manual. Be sure to consult, and adhere to the instructional
materials, labels and warnings accompanying the other
components of your PFAS as well.
4. Check the installation of the anchorage connector to which you
intend to attach this Cable Anchor Extender. Ensure that it has
been inspected and installed according to the manufacturer’s
instructions and that it is firmly attached to the anchorage.
5. Attach the snap hook at the end of this Cable Anchor Extender to
the attachment connector on your anchorage connector. Ensure
that the gate closes and locks automatically, and that the
connection is compatible.
6. Ensure your Full Body Harness is properly donned and adjusted
and that your connecting device is securely attached to your
back D-ring. Tie-off to the Cable Anchor Extender with your
connecting device.
7. Proceed cautiously with your work. Do not run, jump or over-
reach. While moving, the Ratcheting/Sliding Beam Anchor
should glide on the beam, allowing you greater mobility. If it
does not glide smoothly, then check to ensure the D-ring on the
Beam Anchor is centered on the beam. Also check for jagged
edges, fasteners, paint build-up welding spatter or other
obstructions. Any type of obstruction or any sudden
movement may cause the Beam Anchor to seize-up on the
beam, causing you to lose your footing. Move with care and
deliberation at all times while working at heights.
8. Do not allow your connecting device to pass under your arm or
between your legs – severe injury or death may result. Also
avoid sharp edges which may damage your connecting device in
the event of a fall.