FallTech Sling Anchors - Manual (Page 5)

9
as part of a complete personal fall arrest system which maintains a
safety factor of at least two; and under the supervision of a qualified
person.”
Ensure that the structure to which you are attaching your anchorage
connector is capable of meeting the above requirements and that your
anchorage connector is installed in accordance with the manufacturer’s
instructions. Also be sure to check that the anchorage connector is
compatible with your connecting device (lanyard, SRL, vertical lifeline)
and that it securely retains the connecting device without inhibiting its
function. If you are unable to determine whether your connecting device
and your anchorage are compatible, please immediately consult with a
competent person or your immediate supervisor. For more details on
anchorages, please see section 5 of this instruction manual.
2.2: Body-wear
Body wear for any application where this Beam Anchor is to be used
will be defined as a full body harness specifically manufactured for fall
arrest. If being used for restraint applications where the user is restricted
from reaching a fall hazard, a body belt may be used as an alternative.
Be sure to read and follow the manufacturer’s instructions included with
your full body harness or restraint belt at the time of purchase.
2.3: Connectors/Connecting Devices
Connectors and Connecting Devices are terms that are sometimes
used interchangeably. It is important to note the differences between
these two terms in order to help distinguish the parts that these
components play in the rigging of your PFAS. In both cases, these
products/components are required to have a minimum static strength of
5,000 lbs. For additional details on requirements for connectors and
connecting devices, see OSHA 1926.502 at www.osha.gov as
referenced in section 1, advisory #1.
A connector is any metallic, mechanical element such as a
carabiner, snap hook or rebar hook that physically links one or more
elements of a your PFAS together in a manner such that they will remain
engaged to one another unless they are intentionally disengaged.
A connecting device is an element that connects your full body
harness to the anchorage in an effort to ensure that you remain attached
or tethered to the structure upon which you are working. In other words,
the connecting device is that element which secures you to your
anchorage.
10
2.4: Deceleration Devices
A deceleration device is the element of a Personal Fall Arrest
System (PFAS) which is activated during a fall event and reduces the
forces exerted on the user’s body and on the anchorage during the arrest
of the fall. In the case of Shock-Absorbing Lanyards and Self-Retracting
Lifelines, these products are both a connecting device and a deceleration
device as they will keep you attached to your anchorage and will reduce
the forces on your body in the event of a fall.
2.5: Fall Arrest
Fall Arrest is an area of Fall Protection which focuses on stopping a
fall once it has occurred. Personal Fall Arrest Systems typically consist
of an anchorage, a full body harness and a self-retracting lifeline, shock-
absorbing lanyard or other deceleration device designed to bring a falling
user to a stop in the shortest possible distance while limiting the force
imparted to the user’s body.
2.6: Fall Restraint
Fall Restraint is an area of Fall Protection devoted to restraining the
user of the system in a manner which restricts his or her access to the
fall hazard in a manner such that they cannot be subjected to a fall. A
typical Fall Restraint System consists of an anchorage, a full body
harness or a restraint belt and a restraint lanyard. A Shock-Absorbing
Lanyard or a Self-Retracting Lifeline should never be utilized in a
restraint application as it they not capable of restricting a user’s access
to fall hazards.
2.7: Work Positioning
Work Positioning is an area of Fall Protection devoted to allowing a
user to work on a vertical surface by means of a positioning assembly,
and restricting the user’s exposure to a fall of no more than two feet.
Typical positioning assemblies consist of a large rebar hook and a length
of chain, rope, wire rope or webbing with a double locking snap hook on
either end. These snap hooks are attached to d-rings on the hips or on
the waist of the user’s full body harness, with the rebar hook attached to
the structure upon which the user is working. An SAL or an SRL should
never be used for work positioning, nor should they ever be attached to a
side or hip d-ring on a full body harness. However, while rigged for
work positioning, the user should always have an SAL or SRL
attached to the back d-ring of their full body harness and tied-off to
the structure on which they are positioning as a back up device.