Van Air Systems HL-200 - HL2000 - Manual (Page 2)

PAGE 2
HANDLING THE DRYER SECTION 1
SAFETY INSTRUCTIONS SECTION 2
2.3 OPERATION
DO NOT OPERATE DRYER IF EITHER VESSEL IS LEAKING.
IMMEDIATELY TAKE THE DRYER OUT OF SERVICE.
ANY DAMAGE TO THE VESSELS CAN MAKE THEM UNSAFE
TO USE. INSPECT OUTSIDE AND INSIDE OF VESSELS
REGULARLY FOR CORROSION AND ANY DAMAGE (I.E.,
DENTS, GOUGES OR BULGES). IF DAMAGED, TAKE OUT OF
SERVICE IMMEDIATELY.
DO NOT OPERATE THIS DRYER ABOVE THE MAXIMUM RATED
WORKING PRESSURE.
OPERATING CONDITIONS FOR PROPER PERFORMANCE OF
THIS DRYER ARE DIFFERENT THAN MAXIMUM OPERATING
CONDITIONS FOR THE VESSELS. BE SURE TO CHECK THE
DRYER OPERATING CONDITIONS. SEE SECTION 3.1.
USE THIS DRYER FOR COMPRESSED AIR ONLY.
AIR FROM THIS DRYER IS NOT SUITABLE FOR BREATHABLE
AIR SYSTEMS WITHOUT FURTHER TREATMENT.
DO NOT OPERATE THIS DRYER IF EITHER VESSEL HAS BEEN
DAMAGED BY FIRE. TAKE OUT OF SERVICE IMMEDIATELY
AND NOTIFY YOUR CERTIFYING AUTHORITY.
2.4 MAINTENANCE
DO NOT REMOVE, REPAIR, OR REPLACE ANY ITEM ON THE
DRYER WHILE IT IS PRESSURIZED. TURN OFF MAIN POWER
TO THE DRYER AND DEPRESSURIZE THE DRYER COM-
PLETELY BEFORE STARTING MAINTENANCE PROCEDURES.
DO NOT WELD OR GRIND EITHER VESSEL. IT WILL NOT BE
SAFE TO OPERATE. (Note: Any uncertified alteration to the
vessels VOIDS the ASME Code Certification and the
Warranty.)
If the unit is to be stored outdoors, it MUST BE covered completely.
The cover must be adequate to prevent rain or snow from
accumulating on the dryer. The location must be free of standing
water and mud. The preferred location, if outdoors, is on a paved
surface.
1.3 EQUIPMENT CHECK
Inspect the dryer for any damage that may have occurred during
shipment. Inspect all fittings, piping connections, fasteners, etc. for
loose connections. Also check gauges and lights for cracks or
breakage.
IF DRYER HAS BEEN DAMAGED DURING SHIPMENT:
(1)
NOTIFY CARRIER IMMEDIATELY AND FILE A CLAIM.
(2) CONSULT FACTORY BEFORE OPERATING THE DRYER.
1.1 HANDLING INSTRUCTIONS
WARNING
DO NOT LIFT THE DRYER BY PIPING OR CONTROL BOX. THESE
COMPONENTS ARE NOT DESIGNED TO HOLD THE WEIGHT OF THE
DRYER. PERSONAL INJURY AND/OR EQUIPMENT DAMAGE MAY
RESULT.
Lift the dryer by the lifting lugs on both vessels.
If the unit is to be lifted by an overhead device, attach the lifting chains or
cables to the skid angle and the vessel lifting lugs. Make sure that the
chains or cables are clear of all piping and dryer components.
1.2 STORAGE INSTRUCTIONS
The ideal place to store the unit is indoors. The location should be free
from corrosive gasses and extreme humidity. These conditions will cause
damage to the unit. The unit should be covered with a tarpaulin to keep
the unit clean.
2.1 HANDLING
DO NOT LIFT THE DRYER BY PIPING OR CONTROL BOX. THESE
COMPONENTS ARE NOT DESIGNED TO HOLD THE WEIGHT OF
THE DRYER. PERSONAL INJURY AND/OR EQUIPMENT DAMAGE
MAY RESULT.
WHEN LIFTING THE DRYER, ALWAYS USE THE LIFTING LUGS
PROVIDED ON BOTH TOWERS.
MAKE SURE THAT ALL LIFTING EQUIPMENT IS CAPABLE OF
SUPPORTING THE WEIGHT OF THE DRYER.
2.2 INSTALLATION
BEFORE STARTING INSTALLATION PROCEDURES, TURN OFF
POWER TO THE AREA WHERE THE DRYER WILL BE INSTALLED.
SERIOUS PERSONAL INJURY MAY RESULT IF THIS SAFETY RULE
IS NOT FOLLOWED.
THESE ASME CODE VESSELS MUST BE PROTECTED BY
PRESSURE RELIEF VALVES. Refer to OSHA 1910.169 Par. b, Sub.
Par (3) and ASME Boiler and Pressure Vessel Code, Section VIII,
Division 1, UG-125 through UG-136. Also comply with all state
and local codes.
WHEN INSTALLING AND OPERATING THIS EQUIPMENT, COMPLY
WITH THE NATIONAL ELECTRICAL CODE AND ALL APPLICABLE
FEDERAL, STATE, AND LOCAL CODES.
WHEN INSTALLING THIS DRYER, MAKE SURE THAT THE NEMA
RATING OF THE CONTROL BOX IS APPLICABLE TO THE
INSTALLATION.
MAKE SURE THAT ALL CUSTOMER SUPPLIED WIRING AND
ELECTRICAL DEVICES ARE PROPERLY SIZED TO HANDLE THE
ELECTRICAL REQUIREMENTS OF THE DRYER.
ALWAYS WEAR EYE PROTECTION, GLOVES AND A RESPIRATORY
PROTECTIVE DEVICE WHEN HANDLING THE DESICCANT.
DESICCANT DUST MAY CAUSE EYE AND SKIN IRRITATION. AVOID
BREATHING THE DUST AND PROLONGED CONTACT WITH THE
SKIN.
FIRST AID IN CASE OF EYE CONTACT WITH DESICCANT DUST;
IMMEDIATELY FLUSH THE EYES WITH PLENTY OF WATER FOR AT
LEAST 15 MINUTES. CONSULT A PHYSICIAN.