Document Outline

• 68X216807 - RES1000_Rev4.pdf
  • 68X216807 - RES1000.pdf
    • 1 Introduction
      • 1.1 Description of Unit
      • 1.2 Applications
    • 2 Assembly and Installation
      • 2.1 Measurement and Control System
      • 2.2 Unit Dimensions
    • 3 Electrical Connection
      • 3.1 Connection Diagram
      • 3.2 Back Panel
    • 4 Overview
      • 4.1 Keypad and Display
        • 4.1.1 Keypad
        • 4.1.2 Display
      • 4.2 Function Groups
      • 4.3 Control Concept
    • 5 Measurement
      • 5.1 Display in Measurement mode
        • 5.1.1 Check electrode performance
        • 5.1.2 Checking set points
      • 5.2 Security Codes
        • 5.2.1 How to enter and change parameters in Calibration mode
          • 5.2.1.1 Clearing Calibration security code from display
        • 5.2.2 How to enter and change parameters in Advanced Setup mode
          • 5.2.2.1 Clearing Advanced Setup security code from display
    • 6 Calibration Mode
      • 6.1 Resistivity Calibration
    • 7 Advanced Set-Up Mode
      • 7.1 Temperature Coefficient sub-function
        • 7.1.1 Selecting Pure-water or Linear Temperature Coefficient
      • 7.2 Temperature calibration (ATC mode only)
        • 7.2.1 Setting manual temperature compensation
      • 7.3 Control Relay A/Control Relay B (SP1/SP2) sub-function
        • 7.3.1 Entering the Set point 1 (Set point 2) sub-function
        • 7.3.2 Selecting the set point values
        • 7.3.3 Choosing High or Low set points
        • 7.3.4 Selecting a hysteresis (dead band) value (0.000 to 0.200 m( or 0.00 to 2.00 m()
        • 7.3.5 Setting an on-delay time lag
        • 7.3.6 Setting an off-delay time lag
      • 7.4 Controller (Cntr) sub-function
        • 7.4.1 Entering the Controller sub-function
        • 7.4.2 Choosing the controller type (limit or proportional)
        • 7.4.3 Choosing break/make contact relay type
        • 7.4.4 Selecting proportional range value Xp
        • 7.4.5 Maximum Pulse Length (tPL) or Maximum Frequency (FPF)
      • 7.5 Measurement Range sub-function
        • 7.5.1 Entering the Measuring Range sub-function
        • Selecting Measuring Range sub-function
        • 7.5.3 Measurement Range available in the Controller
        • 7.5.4 Current Output (rng) sub-function
        • 7.5.5 Choosing the output type
        • 7.5.6 Selecting Resistivity value at 0(4)mA
        • 7.5.7 Selecting Resistivity value at 20mA
      • 7.6 Configuration (ConF) sub-function
        • 7.6.1 Entering Configuration sub-function
        • 7.6.2 Selecting Filter Function and the Alarm or Wash Function
        • 7.6.3 Selecting the alarm time lag (if the relay 3 is set to Alarm)
        • 7.6.4 Selecting steady or pulse contact for the alarm relay (if the relay 3 is set to Alarm)
        • 7.6.5 Wash Contact (if the relay 3 is set to Wash)
        • 7.6.6 Input Line Resistance Adjust
        • 7.6.7 Reverting to factory default settings
      • 7.7 Calibration (CAL) sub-function
        • 7.7.1 Entering Calibration mode from Advanced Set-up mode
    • 8 Auto/Manual Mode
      • 8.1 Auto mode (mode after switch-on)
      • 8.2 Manual mode
    • 9 Technical Specifications
    • 10 General Information
      • 10.1 Packaging
      • 10.2 Return of Goods
      • 10.3 Guidelines for Returning Unit for Repair
    • 11 Appendices
      • Appendix 1 – Jumper Positions
      • Appendix 2 – Conductivity / Resistivity of Various Aqueous Solutions at 25oC
      • Appendix 3 - Simple Explanation on the Function of Hysteresis
      • Appendix 4 – Pure Water Curve