Document Outline

• Introduction
• SAFETY PRECAUTIONS
• CAUTION ON INSTALLATION LOCATION
• Contents
• PRODUCT OUTLINE
  • Checking delivered items
  • NAME AND FUNCTION OF EACH PART
    • Flow Transmitter
    • Small/middle size detector
    • Large size detector
    • Small diameter/High temperature detector
• INSTALLATION AND BEFORE START OF OPERATION OF THE FLOW TRANSMITTER
  • Outline of installation procedure
• INSTALLATION
  • Installation location of flow transmitter
  • Installation location of detector
    • Length of straight pipe
    • Mounting position
  • Installation of flow transmitter
    • Wall Mounting Transmitter
    • Pipe Mounting Transmitter
  • Flow transmitter wiring
    • Cautions in wiring
    • Applicable wires
    • Treatment of wiring port
    • Wiring to each terminal
• Parameter
  • Description of display/setting unit
  • Composition of key operation
  • Parameter initial value list
  • Parameter protection
  • Display language
    • How to select the language
  • Checking and Setting of Piping Specifications/Detector
    • Checking piping parameter
    • Piping parameter setting method
  • Zero Adjustment
  • Setting of unit
    • How to set the unit system
    • How to set the flow rate unit
    • How to set the total unit
  • Output Setting
    • Setting of flow rate range
      • Setting of flow rate range (single range)
      • Setting of analog output at error (Burnout)
      • Output limit
    • Setting the total
      • Setting the total pulse (pulse value, pulse width)
      • Setting the preset value
      • TOTAL mode (total reset, start, stop)
      • Determining how to dispose of total at error (BURNOUT)
    • Setting the DO output
      • How to validate the total pulse output
    • Setting the LCD indication
    • Setting the damping
    • Setting the low flow rate cutting
  • Application operation of parameter
    • Setting automatic 2 ranges
    • Setting the Bi-directional range
    • Setting the Bi-directional auto 2 range
    • Rate limit
    • Setting the DO output
      • How to validate outputting the FULL SCALE 2
      • How to validate the alarm output
      • Setting the flow switch
      • How to validate the total switch
      • How to validate the range over output and pulse range over output
      • How to validate the output at the minus direction action
    • Setting the DI input
      • Invalidating the DI input
      • How to validate the total preset with the external contact.
      • How to validate the zero adjustment with the external contact.
    • How to compensate the measurement value
    • Setting of the operation mode
  • MAINTENANCE MODE
    • How to calibrate the analog output
    • How to set the constant current output
    • How to check the action of total pulses
    • How to check the status output
    • How to check the DI input
    • How to validate the test mode (simulated flow rate output)
    • How to validate a serial transmission (RS-232C/RS-485)
    • How to set the ID No.
    • How to confirm the software version
    • Initializing setting parameters
    • How to set the detailed setting
• Mounting of detector
  • Detector mounting procedure
    • Mounting of detector
    • Image figure of mounting dimension
  • Selection of mounting position
  • Selection of mounting method
  • Processing of mounting surface
  • How to determine the mounting position
  • Selection of acoustic couplant
  • Cable end treatment
    • Cable end treatment for SX2
    • Cable end treatment for SX1
  • Mounting small-diameter and medium size sensor (SX1-A, SX2-A)
    • Connection of sensor cable
    • Assembling procedure of the sensor
    • Mounting method on the pipe
      • In case of V method
      • In case of Z method
  • Mounting large size detector (SX1-C)
    • Connection of sensor cable
    • Mounting method on the pipe
  • Mounting small diameter detector (SX2-A)
  • Mounting high temperature detector (SX2-B)
    • Mounting of detector (in case of V method)
    • Mounting of detector (in case of Z method)
• CHECK AND MAINTENANCE
  • Daily Check
  • Periodic Inspection
    • Checking zero point
    • Reapplying grease
    • How to measure the insulation resistance
  • How to replace the fuse
  • How to replace the relay
  • How to replace the LCD
  • ERROR AND REMEDY
    • Display error
      • Checking the LCD/LED
      • Checking the LED lit in red
      • Checking the RAS information
    • Displaying the data in maintenance mode
    • Keying is abnormal
    • Error in measured value
    • Error in analog output
    • Checking received waveforms
      • How to connect the oscilloscope
      • Checking sending/receiving
    • Remedying a hardware fault
• Appendix
  • How to make gauge paper
  • Piping data