Sterlco Micro Series Water Temperature Control Unit - Manual (Page 14)

3200 Series
14 ACS 3216 Operators Manual
INPUT/OUTPUT LIST 1 ‘I O -1 ’
Name Scrolling Display Parameter Description Value Default Access Level
1.SRC.A I/O 1 SOURCE A None No event connected to the output
AL1 Alarm 1 1.SRC.B I/O 1 SOURCE B
AL2 Alarm 2
AL3 Alarm 3 1.SRC.C I/O 1 SOURCE C
AL4 Alarm4
ALL.A All alarms
nw.AL Any new alarm
Ct.AL CT alarm, load, leak & overcurrent
Lbr Loop break alarm
Sbr Sensor break alarm
t.End Timer end status
t.run Timer run status
mAn Manual status
rmt.F Remote fail
Pwr.f Power fail
1.SRC.D I/O 1 SOURCE D
These parameters only
appear when the channel
function is a Digital output,
i.e. 1.FUNC = d.out
Selects an event status to be
connected to the output
channel.
The output status is the
result of an OR of Src A,
Src B, Src C, and Src D
Up to four events can,
therefore, operate the output
prg.e Programmer event.
none Conf
None Input not used
Ac.AL Alarm acknowledge
SP2 Setpoint 2 select
Loc.b Front keypad disable (keylock)
t.res Timer/programmer reset
t.run Timer/programmer run
t.rrS Timer/programmer run/reset. Make to
run, break to reset
t.HLd Timer/programmer hold
Man Manual status
Sby Standby mode. In this mode control
outputs go to zero demand
Rmt Remote digital setpoint select
Rec Recipe select through IO1 digital input
UP Remote key ‘Up’
1 . D . I N DIGITAL INPUT
FUNCTION This parameter is only
applicable to I/O 1 and only
appears if the channel
function is a Digital IP
i.e. 1.FUNC =
d.in
Only one function may be
activated by a physical input
Dwn Remote key ‘Down’
Ac.AL Conf
1 . P L S OUTPUT 1
MINIMUM PULSE
TIME Minimum output on/off
time.
Only applies to time
proportioning outputs and
prevents relays from
switching too rapidly
0.0 to
150.0
Auto or 1.0 to 150.0 seconds
Auto = 110mS
5.0 sec
for
relay.
Auto for
logic
Conf
1.SENS I/O 1 SENSE To configure the sense of
the input or output channel nor
Inv Normal
Inverted nor Conf
0.20 0-20mA output 1 . r n g DC OUTPUT
RANGE To configure 0-20mA or 4-
20mA output
Only appears if the output
module is DC output
4.20 4-20mA output
L3
OUTPUT LIST 2 ‘op-2’
Name Scrolling
Display
Parameter Description Value Default Access Level
none Output not fitted
rely Relay output
L.OP Logic output (3200 only)
dC.Op 0-20mA output.
2 . i d OUTPUT 2
TYPE Output channel 2 hardware
type
SSR Triac output
As ordered Read only
None Disabled. If disabled no further
parameters are shown
d.out Digital output
UP Valve open codes VC and VP only
Dwn Valve close codes VC and VP only
Heat Heat output
CooL Cool output
d.out Conf
w.SP Working setpoint re-transmission
2.FUNC FUNCTION Output channel 2 function
If the instrument is ordered as
valve positioner (codes VC or
VP), only options available are
,
none, d.out, UP, or
dwn
Note: If output 2 is set to
Up
ensure the other valve
position output is set to
dwn
PV Process variable re-transmission
Shown if I/O 2 TYPE =
dc.OP Retransmission