GE JS630SFSS User Manual

Js630sf, 30" slide-in electric range

Advertising
background image

JS630SF

GE

®

30" Slide-In Electric Range

Dimensions and Installation Information (in inches)

Listed by

Underwriters

Laboratories

For answers to your Monogram

®

or GE

®

appliance questions, visit our website at

geappliances.com or call GE Answer Center

®

service, 800.626.2000.

All GE ranges are equipped with

an Anti-Tip device. The installation

of this device is an important,

required step in the installation

of the range.

320632

Specification Created 6/13

Acceptable

Electrical

Outlet Area

30" Min.

30" Min.

Shave Raised Edge To Clear

31-1/8" Wide Control Panel

Excluding Model JSS28

2-7/8"

To Front

Surface Of

Countertop

20-5/8" Door

Clearance

From Front

Surface of

Countertop

31-1/4

30

25-3/4*

Recommended

6" Min.

From Walls

23-3/16

15" Min.

4

2-1/2

30

25

9/16

7-1/2

2-1/2

Accessory

Backguard

JXS32

24

36-1/4

(excluding handle)

*Total depth from wall to

front of closed oven door

including handle is 28-1/2.

35-7/8"–38"

from floor to

countertop

If the countertop area is not flat, excess tension may be applied to the glass cooktop, causing breakage and
voiding the warranty. Make sure the wall covering, countertop, flooring and cabinets around the range can
withstand the heat (up to 200°F) generated by the range.

A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or metal cabinet, or

allow a 24" minimum when bottom of wood or metal cabinet is protected by no less than 1/4"-thick
flame-retardant millboard covered with no less than No. 28 MSG sheet metal (.015" thick), .015"-thick stainless
steel, .025" aluminum or .020" copper.

B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop.

However, a minimum 6" spacing to surfaces less than 15" above the cooktop and adjacent cabinetry
is recommended to reduce exposure to steam, grease splatter and heat. Allow 1/4" minimum
clearance at the back wall.

To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space above the
cooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk can be reduced
by installing a range hood that projects at least 5" beyond the front of the cabinets.

23-3/16

30

30

If you are NOT using the

Filler strip or Backguard:

If you are using the

Filler strip or Backguard:

25

Acceptable

Electrical

Outlet Area

30" Min.

30" Min.

Shave Raised Edge To Clear

31-1/8" Wide Control Panel

Excluding Model JSS28

2-7/8"

To Front

Surface Of

Countertop

20-5/8" Door

Clearance

From Front

Surface of

Countertop

31-1/4

30

25-3/4*

Recommended

6" Min.

From Walls

23-3/16

15" Min.

4

2-1/2

30

25

9/16

7-1/2

2-1/2

Accessory

Backguard

JXS32

24

36-1/4

(excluding handle)

*Total depth from wall to

front of closed oven door

including handle is 28-1/2.

35-7/8"–38"

from floor to

countertop

If the countertop area is not flat, excess tension may be applied to the glass cooktop, causing breakage and
voiding the warranty. Make sure the wall covering, countertop, flooring and cabinets around the range can
withstand the heat (up to 200°F) generated by the range.

A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or metal cabinet, or

allow a 24" minimum when bottom of wood or metal cabinet is protected by no less than 1/4"-thick
flame-retardant millboard covered with no less than No. 28 MSG sheet metal (.015" thick), .015"-thick stainless
steel, .025" aluminum or .020" copper.

B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop.

However, a minimum 6" spacing to surfaces less than 15" above the cooktop and adjacent cabinetry
is recommended to reduce exposure to steam, grease splatter and heat. Allow 1/4" minimum
clearance at the back wall.

To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space above the
cooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk can be reduced
by installing a range hood that projects at least 5" beyond the front of the cabinets.

23-3/16

30

30

If you are NOT using the

Filler strip or Backguard:

If you are using the

Filler strip or Backguard:

25

ADA qualified based

on Uniform Federal

Accessibility Standards

*

Receptacle Locations: Locally approved flexible service cord or conduit must

be used because terminals are not accessible after range installation. See

shaded area in drawing for location of electrical outlet box. Recommended

outlet locations allow range to be installed directly against rear wall.
Note: This appliance has been approved for 0” spacing to adjacent

surfaces above the cooktop. However, a 6” minimum spacing to surfaces

less than 15” above the cooktop and adjacent cabinet is recommended

to reduce exposure to steam, grease splatter and heat.
Installation Information: Before installing, consult installation insgtructions

for current dimensional data and additional requirements

Optional Kits For Slide-In

Electric Ranges

(Available At Additional Cost)
Accessory Backguards

(Attaches to the back of range

as a backguard when unit is

installed in 30" free-standing

cutout)

JXS32SS (Stainless) - 4" High

JXS32BB (Black) - 4" High

Body Sides

(Slide-in ranges are sold

without sides installed. Can

be installed on either left

or right when unit has one

exposed side [no cabinet

adjacent]. Kit contains

1 body side)

JXS77BB (Black)
Rear Filler Strip

WB07T10680 - Black Filler Strip Assembly

Optional Lower Trim Kits

(If counter height is greater

than 36.5", a lower trim kit

is recommended to extend

the useful height to 38"

maximum)

JXS56BB – Black

Acceptable

Electrical

Outlet Area

30" Min.

30" Min.

Shave Raised Edge To Clear

31-1/8" Wide Control Panel

Excluding Model JSS28

2-7/8"

To Front

Surface Of

Countertop

20-5/8" Door

Clearance

From Front

Surface of

Countertop

31-1/4

30

25-3/4*

Recommended

6" Min.

From Walls

23-3/16

15" Min.

4

2-1/2

30

25

9/16

7-1/2

2-1/2

Accessory

Backguard

JXS32

24

36-1/4

(excluding handle)

*Total depth from wall to

front of closed oven door

including handle is 28-1/2.

35-7/8"–38"

from floor to

countertop

If the countertop area is not flat, excess tension may be applied to the glass cooktop, causing breakage and
voiding the warranty. Make sure the wall covering, countertop, flooring and cabinets around the range can
withstand the heat (up to 200°F) generated by the range.

A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or metal cabinet, or

allow a 24" minimum when bottom of wood or metal cabinet is protected by no less than 1/4"-thick
flame-retardant millboard covered with no less than No. 28 MSG sheet metal (.015" thick), .015"-thick stainless
steel, .025" aluminum or .020" copper.

B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop.

However, a minimum 6" spacing to surfaces less than 15" above the cooktop and adjacent cabinetry
is recommended to reduce exposure to steam, grease splatter and heat. Allow 1/4" minimum
clearance at the back wall.

To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space above the
cooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk can be reduced
by installing a range hood that projects at least 5" beyond the front of the cabinets.

23-3/16

30

30

If you are NOT using the

Filler strip or Backguard:

If you are using the

Filler strip or Backguard:

25

Acceptable

Electrical

Outlet Area

30" Min.

30" Min.

Shave Raised Edge To Clear

31-1/8" Wide Control Panel

Excluding Model JSS28

2-7/8"

To Front

Surface Of

Countertop

20-5/8" Door

Clearance

From Front

Surface of

Countertop

31-1/4

30

25-3/4*

Recommended

6" Min.

From Walls

23-3/16

15" Min.

4

2-1/2

30

25

9/16

7-1/2

2-1/2

Accessory

Backguard

JXS32

24

36-1/4

(excluding handle)

*Total depth from wall to

front of closed oven door

including handle is 28-1/2.

35-7/8"–38"

from floor to

countertop

If the countertop area is not flat, excess tension may be applied to the glass cooktop, causing breakage and
voiding the warranty. Make sure the wall covering, countertop, flooring and cabinets around the range can
withstand the heat (up to 200°F) generated by the range.

A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or metal cabinet, or

allow a 24" minimum when bottom of wood or metal cabinet is protected by no less than 1/4"-thick
flame-retardant millboard covered with no less than No. 28 MSG sheet metal (.015" thick), .015"-thick stainless
steel, .025" aluminum or .020" copper.

B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop.

However, a minimum 6" spacing to surfaces less than 15" above the cooktop and adjacent cabinetry
is recommended to reduce exposure to steam, grease splatter and heat. Allow 1/4" minimum
clearance at the back wall.

To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space above the
cooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk can be reduced
by installing a range hood that projects at least 5" beyond the front of the cabinets.

23-3/16

30

30

If you are NOT using the

Filler strip or Backguard:

If you are using the

Filler strip or Backguard:

25

KW Rating

240V 11.9
208V 8.9

Breaker Size

240V 40 Amps

208V 40 Amps

Note: Check local codes for required breaker size.

Advertising