GE JV347HWW - Manual (Page 5)

CAUTION:
Let the light bulb
cool completely before removing. A warm or
hot bulb may break if touched with a moist
cloth or hand.
Remove the bulb and replace it with a type
A15 incandescent light bulb with an ordinary
screw base, not more than 60 Watts, or a
type A17 or T2 Compact Fluorescent (CFL)
light bulb with an ordinary screw base,
not more than 13 Watts. NOTE: Use only
incandescent bulbs in models RN328, JN327
and JV338.
IMPORTANT: For installation, handling and
disposal precautions, refer to the fluorescent
bulb packaging literature.
To remove the light cover
(on some models):
‡3UHVVWKHVLGHVZLWKWZRILQJHUVXQWLOWKH
side prongs are released.
‡ /LIWWKHOLJKWFRYHUDQGVOLGHLWWRZDUG\RX
in one motion.
To replace the light cover:
‡ ,QVHUWWKHSURQJORFDWHGDWWKHHQGRIWKH
cover into the top opening.
‡ *HQWO\SXVKWKHFRYHUXSDQGSUHVVWKH
sides to fit the side prongs into the side
openings.
‡ 5HOHDVHDQGWKHFRYHUZLOOORFNLQSRVLWLRQ
Hood Light
The charcoal filter cannot be cleaned.
It must be replaced. Order filter no.
WB02X10700. Replacement filters can be
ordered from your GE supplier.
If the hood is not vented to the outside, the
air will be recirculated through a disposable
charcoal filter that helps remove smoke and
odors.
The charcoal filter should be replaced after 6
to 12 months (depending on hood usage).
To remove:
Pull down on the center of the front edge
of the filter. The filter will then slip out of the
retaining tabs on the back.
To replace:
Slip the back edge of the filter into the
retaining tabs and push the front edge up
until it snaps into place.
&KDUFRDO)LOWHU³5HFLUFXODWLQJ,QVWDOODWLRQV2QO\
Do not use steel-wool pads or other
abrasive cleaners. They will scratch the
surface.
Clean grease-laden surfaces of the hood
frequently. To clean the hood surface, use
a hot, damp cloth with a mild detergent
suitable for painted surfaces. About one
tablespoon of ammonia may be added to
the water. Use a clean, hot, damp cloth to
remove soap. Dry with a dry, clean cloth.
NOTE: When cleaning, take care not to
come in contact with filters and other non-
enameled surfaces.
CAUTION:
When cleaning the
hood surfaces, be certain that you do not
touch the light bulb with moist hands or
cloth. A warm or hot light bulb may break if
touched with a moist surface. Always let the
light bulb cool completely before cleaning
around it.
Painted Surfaces (on some models)
Replaceable charcoal filter
5
NOTE: DO NOT rinse, or put charcoal
filters in an automatic dishwasher.
Light cover
Do not use a steel-wool pad; it will scratch
the surface.
To clean the stainless steel surface, use
warm sudsy water or a stainless steel cleaner
or polish. Always wipe the surface in the
direction of the grain. Follow the cleaner
instructions for cleaning the stainless steel
surface.
To inquire about purchasing stainless steel
appliance cleaner or polish, or to find the
location of a dealer nearest you, please call
our toll-free number:
National Parts Center
800.626.2002
GEApplianceParts.com
Stainless Steel Surfaces (on some models)
When using an energy saving bulb in your GE hood
make sure you use either:
GE Long Life Energy Smart ™ Spiral ® T2
Product Code: 85383
Description: FLE13HT2/2/SW/CD
or
GE Long Life Energy Smart ™ A17
Product Code: 47486
Description: FLE11/2/A17XL/CD
Available at www.gelighting.com