GE ZET938SMSS - Manual (Page 10)

10
CUTOUT
HEIGHT
51 13/16" MIN.
51 15/16" MAX.
5"
CUTOUT
WIDTH
28 1/2" MIN.
28 5/8" MAX.
47" TO
BOTTOM OF
JUNCTION BOX
JUNCTION BOX
LOCATION
ALLOW 11/16"
FOR OVERLAP
OF THE OVEN
OVER SIDE EDGES
OF CUTOUT
THE OPENING
BETWEEN INSIDE
WALLS MUST
BE AT LEAST
28 1/2"WIDE
ALLOW 1" FOR
OVERLAP
ON OVEN TOP
AND BOTTOM
OF CUTOUT
21"
ALLOW A MINIMUM OF 21"
FOR CLEARANCE TO
ADJACENT CORNERS,
DRAWERS, WALLS ETC.
WHEN THE DOOR
IS OPENED.
30"
CABINET
WIDTH
RECOMMENDED
CUTOUT LOCATION
12" FROM THE FLOOR
Installation Instructions
Cabinet Width 30” (76.2 cm)
Recommended
Cutout Location
from Floor
12” (30.5 cm)
Cutout Depth 23 1/2” (59.7 cm) Min.
Cutout Width 28 1/2” (72.4 cm) Min.
28 5/8” (72.7 cm) Max.
Cutout Height 51 13/16” (131.6 cm) Min.
51 15/16” (131.9 cm) Max.
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For
double ovens, the runners and braces
must support 275 lbs (124 Kg).
Cutout for 30
″
(76.2 cm)
Double Built-In Ovens only
For JTP35, JTP55, JTP75, PT956, PT960, ZET958 models only.
NOTE: If the cabinet does not
have a front frame and the sides
are less than 3/4” (1.9 cm) thick,
shim both sides equally to
establish the cutout width.
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
9 1/2”
(24.1 cm)
Max.
Allow 11/16”
(1.75 cm) for
overlap of oven
over side edges
of cutout
30”
(76.2 cm)
Cabinet
Width
21” (53.3 cm)
Junction Box
Location
(junction box
may be
located in
adjacent
cabinet)
Allow a minimum
of 21” (53.3 cm) for
clearance to adjacent
corners, drawers,
walls, etc. when
door is open
Allow 1” (2.5 cm)
minimum for
overlap of oven
top and 1
1 ⁄
4
”
(3.2 cm) overlap
of oven bottom
of cutout
Recommended
cutout location
from floor 12” (30.5 cm)
47” (119.4 cm)
Min.
to Bottom of
Junction Box
A
C L 2" x 4" or
EQUIVALENT
RUNNERS
21 5/8"
OVER CENTERLINE
OF CABINET
2” x 4”
(5 cm x 10 cm)
or equivalent
runners level
with bottom
of cutout
21 5/8”
(54.9 cm) Over
Centerline
of Cabinet
Opening
Between
Inside Walls
Must Be At
Least 28 1/2”
(72.4 cm) Wide
Cutout
Width
28 1/2” (72.4 cm)
Min.
28 5/8” (72.7 cm)
Max.
Cutout
Height
51 13/16” 131.6 cm)
Min.
51 15/16” (131.9 cm)
Max.
Suitable
Bracing
to Support
Runners